Oliver 4016 Скачать руководство пользователя страница 13

Electrical Connections

WARNING!

Electrical connections and wiring must be 

done by a qualified electrician.  The machine 

must be properly grounded.  Failure to 

comply may cause serious injury!

This   saw   is   available   in   both   1-Phase   and   3-
Phase versions.  

Electrical Connections for a 3-Phase Unit

This   saw   is   3-Phase,   220V/440V  

pre-wired 

220V

.   If you need to switch the tablesaw from 

220V to 440V have a qualified electrician make 
the   changes.     Oliver   Machinery   recommends 
using a dedicated circuit.

Make   sure   the   voltage   of   your   power   supply 
matches the specifications on the motor plate of 
the machine.

With 3-Phase power verify the blade is turning in 
the proper direction.  Turn the saw on and make 
sure the direction of the blade spins toward the 
user when standing in front of the saw.  If it does 
not,   disconnect   the   power   source   and   reverse 
any two power leads.

Electrical Connections for a 1-Phase Unit

This   saw   is   1-Phase,   220V   only.     Oliver 
Machinery   recommends   using   a   dedicated 
circuit.

Make   sure   the   voltage   of   your   power   supply 
matches the specifications on the motor plate of 
the machine.

Replacing the Blade

The blade guard has been removed for photos, 
but   it   is   possible   to   change   the   blade   without 
removing the blade guard.

1. Disconnect saw from power source.  

2. Remove the table insert and raise the blade 

completely.

3. Use   the   two   provided   arbor   wrenches   to 

loosen the arbor nut, as shown in Figure 25. 
Place one wrench on the arbor nut and one 
on the flats located on the arbor.   Remove 
the nut, flange and blade.

4. Replace   the   blade   followed   by   the   flange 

and arbor nut.   Tighten the arbor nut while 
holding the arbor in place.  

Note:

  Make sure the blade and arbor are clean 

before installing a new blade.   The blade teeth 
should point down when viewing from the front 
of saw.

Figure 25

 

13

Содержание 4016























Отзывы: