Oliver 4016 Скачать руководство пользователя страница 12

Miter Gauge

1. Slide   the   miter   gauge   bar   into   the   miter 

gauge slot in table.   Loosen the handle (A, 
Figure   23)   and   pull   out   indexing   rod   (B, 
Figure 23) to pivot the miter gauge body.

2. Push   the   indexing   rod   in   to   engage   the 

preset stops (C, Figure 23).  

3. Adjust   stops   by  loosening   the   hex  nut   (D, 

Figure   23)   and   adjusting   screw   (E,   Figure 
23).

Note:

   Always make test cuts.  The scale is for 

reference.     There   are   two   holes   in   the   miter 
gauge fence used to attach a wooden fence.

Controls (see Figures 24 & 25)

A.

Emergency   Stop   Button:

 

  Stops   all 

functions of machine.

B.

Start:

   Starts saw blade rotation.   Will not 

work   if   the   “Emergency   Stop”   switch   is 
engaged, or the key is in the  “OFF” position.

C.

Handwheel   Lock:

    There   is   a   handwheel 

lock  on   both   handwheels.     Loosen  lock  to 
turn handwheel and tighten when blade is in 
desired location.

D.

Raising   and   Lowering   Hand   wheel: 

Loosen   hand   wheel   lock.     Turn   handle 
clockwise   to   raise   the   blade.     The   blade 
should   be   1/8”-1/4”   above   the   top   of   work 
piece, or 3-5 blade teeth above the top of 
work piece.  

E.

Tilting   Hand   wheel:

    Loosen   hand   wheel 

lock.   Turn  handle  counter-clockwise  to  tilt 
blade to the left.  

Dust Collection

There is a 4” dust port (G, Figure 25) located on 
the   side   of   saw   cabinet.     Make   sure   dust 
collection   system   has   sufficient   capacity   and 
suction for your tablesaw.   Always turn on dust 
collection system before starting the tablesaw.

Figure 23

Figure 24

Figure 25

12

Содержание 4016























Отзывы: