Okolab UNO-T Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 73

background image

64

12

Technical Specifications

UNO-T

–

Technical Specifications

Temperature

Control Range: 3°C above ambient temperature (minimum temperature set point 25°C) to 60°C
Step size: 0.1°C
Accuracy:

•

± 0.1°C in Sample Control mode

•

± 0.3°C in Chamber Control mode, if the Room Temperature is stable within ± 1°C.

Power Supply

UNO-CONTROLLER

–

Supply Voltage 24 V-DC

Power Consumption

120 W max

Dimension

UNO-CONTROLLER (LxWxH)

129mmx125mmx104mm

UNO-CONTROLLER Weight

0.400 Kg

Table 5. UNO-T Technical Specifications.

UNO-T-H-PREMIXED

–

Technical Specifications

Temperature

Control Range: 3°C above ambient temperature (minimum temperature set point 25°C) to 60°C
Step size: 0.1°C
Accuracy:

•

± 0.1°C in Sample Control mode

•

± 0.3°C in Chamber Control mode, if the Room Temperature is stable within ± 1°C.

GF-REGULATOR input gas

Premixed Gas supply
The premixed gas tank must be equipped with a pressure regulator to decrease the pressure
from the pressure tank to 4 barg (58 psig).

GF-REGULATOR input gas connector Push to fit connector for 6 mm O.D. rigid tube

GF-REGULATOR output gas

0.2

–

1.2 barg

GF-REGULATOR flow rate

0.1 - 0.4 l/min

Humidification Power

85% - 90% Relative Humidity
if the Room Temperature is stable within ±1°C at 23°C, the GF-MIXER-HM (Humidity Module) is
installed away from heating and air conditioning vents and windows /doors that are frequently
open.

Power Supply

UNO-CONTROLLER

–

Supply Voltage 24 V-DC

GF-MIXER-HM (Humidity Module)

–

Supply voltage

24 V DC

Power Consumption

120 W max

Dimension

UNO-CONTROLLER (LxWxH)

129mmx125mmx104mm

UNO-CONTROLLER Weight

0.400 Kg

Humidifier

diameter 72 mm, height 190 mm

Table 6. UNO-T-H-PREMIXED Technical specifications.

«
...
66
67
68
69
70
...
»

Содержание UNO-T










































































Отзывы:

Нет отзывов

Похожие инструкции для UNO-T

Бренд: Garelick Страницы: 2

Бренд: Gardico Страницы: 2

Бренд: OceanSat Страницы: 85

Бренд: P-Q Controls Страницы: 5

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: Harken Страницы: 4

Бренд: Tarmo Страницы: 4

Бренд: Halemeier Страницы: 2

Бренд: IRUDEK Страницы: 19

Бренд: Jacassi Страницы: 5

KEYSTATION 61 MK3

Бренд: M-Audio Страницы: 72

Digital Sound System Processor Dx34

Бренд: Electro-Voice Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды