Okolab UNO-T Скачать руководство пользователя страница 25

Страница: 25 / 73

Connect the WP-

CABLE to “Obj. Heater” connector on the rear panel of UNO

-CONTROLLER (see Figure

22).

OBJ-COLLAR

UNO-CONTROLLER

WP-CABLE

Figure 22. OBJ-COLLAR - Connection.

Tip

►

Connecting cables are equipped with identification tags to guide you through the installation process.

MINI-USB port

The MINI-USB provides the connection for the supplied MINI-USB-OTG cable or a standard MINI-USB

cable.

7.6.1

Connection of MINI-USB-OTG cable

Use the supplied MINI-USB-OTG cable to connect a USB pen drive (not supplied) to UNO-CONTROLLER,

as shown in Figure 23.

USB Pen Drive

MINI-USB-OTG cable

Figure 23. MINI-USB-OTG cable - Connection.

7.6.2

Connection of MINI-USB cable

Use a standard MINI-USB cable to connect UNO-CONTROLLER to a PC, as shown in Figure 24. UNO-

CONTROLLER can communicate with the PC by using:

Содержание UNO-T










































































Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды

Okolab UNO-T, Руководство пользователя

Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды