Okolab H301-NIKON-NZ100/200/500-N Скачать руководство пользователя

Страница: 5 / 17

H301-NIKON-NZ100/200/500-N

User Manual

Rev 03

www.oko-lab.com

Available Lids

The following heated glass Lids are available for H301-NIKON-NZ100/200/500-N:

•

H301-SLIDING-LID

: For easy sample loading and pipetting

–

Included in code

H301-NIKON-NZ100/200/500-N.

Compatible with Mad City Labs NZ100/200 ONLY.

•

H301-KOEHLER-LID*

: Reduces chamber height to 22 mm and allows imaging under Koehler illumination

•

H301-INJECTION-LID*

: Heated glass lid with two small openings (sealed with flexible plastic) allowing injec-

tion or permanent access to the sample. Compatible only with sample holder 1x35

•

H301-LASER-INTERLOCK-LID*

: Heated glass lid with safety switch. Connects to laser controller and automati-

cally turns laser off when lid is lifted. Compatible only with sample holder 1x35

* OPTIONAL

–

not included with H301-NIKON-NZ100/200/500-N

3.1

Sliding lid

The Sliding Lid is a heated glass lid allowing for easy sample loading and pipetting. The Sliding Lid is screwed onto the

chamber.

NOTE:H301-SLIDING-LID is compatible with Mad City Labs NZ100/200 ONLY.

Figure 3 shows chamber dimensions with the Sliding Lid (with and without chamber riser). Figure 4 illustrates how to

remove Sliding Lid, when a different Lid is necessary.

NOTE:

Sliding Lid MUST BE REMOVED when using any other Lid.

The Sliding Lid is fixed onto the chamber with 4

screws. Screws location is indicated by letter A in Figure 4 (image 2 and 3). Keep Sliding Lid fully closed to access

screws labeled A in image 2. Open Sliding Lid to access screws labeled A in image 3.

Distance between focal plane

and upper side of the glass

lid without the chamber riser

Distance between focal plane

and upper side of the glass

lid with the chamber riser

Chamber top view

Sliding Lid

Figure 3. H301-NIKON-NZ100/200/500-N (Sliding Lid comes as standard)

Содержание H301-NIKON-NZ100/200/500-N


















Результаты поиска

Содержание H301-NIKON-NZ100/200/500-N

Отзывы:

Похожие инструкции для H301-NIKON-NZ100/200/500-N

Бренды по названию

Популярные бренды

Okolab H301-NIKON-NZ100/200/500-N, Руководство пользователя

Результаты поиска

Содержание H301-NIKON-NZ100/200/500-N

Отзывы:

Похожие инструкции для H301-NIKON-NZ100/200/500-N

Бренды по названию

Популярные бренды