manualshive.com logo in svg

OKIFAX OF-7, Руководство по обслуживанию на месте

Поделиться
Скачать
OKIFAX OF-7 Скачать руководство пользователя страница 56

3.7.5

Technical Set-up

 

Service 

 can arrange the following technical settings.

Name of

Reference

JO.

Function

Description

Sub-item

1 .   M O D E M

To select the default starting transmission

transmission

rate for the machine which is 9600 bps or

rate

4800 bps.

2. Control of

To select the default sate  for the acoustic line

acoustic line

monitor of the machine whether available or

not.

3.

ignoring 1st 

To arrange the machine to ignore the 1st 

3.7.5.1

signal

signal returned from the remote receiving

station 

 avoid confusion which may be

caused by an echo of the 

 signal returned

back to the remote receiving station which

hastransmitted the 

 signal.

4. Ring response

To select the delay time of the automatic

time

response of the machine.

5.

Density of home

To select the default state for the document

position

density of home position.

6 .   P r o t e c t i v e t o n e  

To select the default state for transmission of

transmission

the protective tone (1800 Hz) against echo

against echo

suppressor.

suppressor

3.7.5.2

 MODEM)

7.

Protective tone

To select the default state for 

transmission 

of

transmission

the protective tone (1700 Hz) against echo

against echo

suppressor.

suppressor

 MODEM)

8. Subscriber line

To equalize the amplitude versus frequency

equalizer

characteristic of the subscriber line installed

setting

the machine and the nearesttelephone

 side)

exchange. (Transmission side)

3.7.5.3

9. Subscriber line

To equalize the amplitude 

versus 

frequency

equalizer

characteristic of the subscriber line installed

setting

the machine and the nearesttelephone

(Rx side)

exchange. (Reception 

side)

3   27

Содержание OF-7















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды