Oki OKIPOS X400 Скачать руководство пользователя страница 11

Страница: 11 / 137

COMMAND DEFAULT

NOTE

Rotation

(1)

Vertical

Reference

Point 0

(1)

Horizontal

Reference

Point

(1)

Character

Pitch

(1)

Base

Reference

Point

H=0,

V=0

(2)

Character

Expansion

(1)

Print Darkness

200

(1)

Print Speed

3 ips

(2)

Notes:

(1) The settings for these commands will revert to the default values when the printer receives an <ESC>Z or an

<ESC>*.

(2) These values transmitted with these commands will remain in effect until a new command is received.

PRINTER CONFIGURATION

The OKIPOS X400 printers are different from other OKI models in that they do not use DIP switches for printer

configuration. Instead, all printer configuration is done via software commands. The parameters that can be

configured are:

Sensor Calibration

Protocol Codes

Print Darkness Range

Sensor Type

RS232 Parameters

Label Tear-Off Position

Backfeed Enable/Disable

Because there are no DIP switches to indicate the current printer settings, a Test Label can be printed that lists

the active settings in the printer. This Test Label lists all of the information a user needs to ascertain the printer

configuration. Test Labels can be printed out by sending a command by software (see page 92) or by using the

FEED button (see User’s Guide).

LABEL SENSING

The OKIPOS X400 printers can use eye-mark (black bar), gap or notch label sensing. The gap and notch sensor

is a transmissive or see-thru type with an infrared light source directed through the label from above and

detected by a separate sensor underneath the label. A reflective sensor is used to detect eye-marks printed on the

All manuals and user guides at all-guides.com

all-guides.com

Содержание OKIPOS X400










































































































































Результаты поиска

Содержание OKIPOS X400

Отзывы:

Oki OKIPOS X400, Руководство по программированию, Страница: 11 / 137

Результаты поиска

Содержание OKIPOS X400

Отзывы: