Oki ML520 страница 125 Скачать руководство пользователя

Страница: 125 / 269

Page: 90

Service Guide ML520/521

Chapter 3 Maintenance & Disassembly

3.2.21 Line Feed Motor Assembly

1. Perform these procedures:

3.2.01

, 3.2.06

, 3.2.07

, 3.2.16

, 3.2.19

, 3.2.20

, and 3.2.21 (this

section).

2. Firmly press down on the line feed motor assembly (1) while tilting the assembly out.

3. Remove the line feed motor assembly.

4. Remove the line feed connection cord (2).

CAUTION:

The line feed idle gear (3) should be removed only if it must be replaced. The claws will break when the
gear is removed. A new gear must be installed.

P/N 51228401 Gear: Line Feed Idle RSPL Both B.2.04

P/N 56510301 Motor: Line Feed (Assembly) RSPL Both B.2.04

Содержание ML520






















































































































































































































































Результаты поиска

Содержание ML520

Отзывы:

Похожие инструкции для ML520

Бренды по названию

Популярные бренды

Oki ML520, Руководство по обслуживанию

Результаты поиска

Содержание ML520

Отзывы:

Похожие инструкции для ML520

Бренды по названию

Популярные бренды