Oki ML520 страница 116 Скачать руководство пользователя

Страница: 116 / 269

Page: 84

Service Guide ML520/521

Chapter 3 Maintenance & Disassembly

3.2.15 Guide Rail and Adjust Cam

1. Perform these procedures:

3.2.01

, 3.2.02

, 3.2.04

, 3.2.10

, 3.2.11

, and 3.2.14

2. Rotate the adjust cam (1) in the direction of arrow A as far as possible.

3. Pull the cam out and remove it.

4. Carefully press the claw (2

location only

) in the base frame down to release the guide rail (3). Do not

press too hard or the claw will break.

5. Use a straight slot screwdriver to slide the guide rail in direction of arrow A.

6. Lift the guide at position B and work the other end of the guide free to remove the guide rail.

7. Remove the ground clip (4)

NOTE:

Installation

After installing the guide rail, check the printhead gap adjustment. Refer to Section

3.3 of this Service Handbook.

P/N 51009701 Guide: Rail Ground Clip RSPL Both B.2.04

Содержание ML520






















































































































































































































































Результаты поиска

Содержание ML520

Отзывы:

Похожие инструкции для ML520

Бренды по названию

Популярные бренды

Oki ML520, Руководство по обслуживанию

Результаты поиска

Содержание ML520

Отзывы:

Похожие инструкции для ML520

Бренды по названию

Популярные бренды