Oki MC560 MFP CX2032 Скачать руководство пользователя страница 91

 

91

Local MFP will not answer the telephone or receive faxes

 

First check to see that the power cord is connected properly. Also check the reception mode 

setting of the machine. This MFP will not receive faxes automatically if the manual receive 

mode is enabled (

See “Manual receive” on page 64 in the CX2032 MFP user’s guide

).

  

 

Documents received are light or have vertical streaks on them, and 
MFP is not out of toner 
 

Gently wipe the lens surface of the MFP’s LED array, and then check to see if the machine is 
working properly.  

(

See ”Cleaning the LED head” on page 126 in the CX2032 MFP user’s guide

).  

 

If the MFP still does not work properly, remove the image drum, tap the toner cartridge, and 

slowly swing it 20 to 30 degrees vertically several times. Be careful not to let the toner leak 
from the cartridge. If this does not work, the image drum unit may need to be replaced.  

 

MFP is set for delayed transmission but it did not

 

 Check the display to make sure that the MFP is set to the correct time and date  

(

See “Initial set up” on page 58

 

in the CX2032 MFP user’s guide

). 

 

MFP will not poll a remote machine  

 Call the person at the remote machine and make sure that they have loaded documents and 

that their machine is set to polling transmission mode.  

 

MFP is connected to a PBX but it is not possible to dial out  

Be certain that the dial prefix is entered before the telephone number for each number dialed 
or programmed into the MFP. 

 (

See “Connecting to a PBX” on page 62

 

in the CX2032 MFP user’s guide

). 

 

 

MFP always answers before it’s possible to use the external telephone  

 If an external telephone is connected, change the MFP.s ring response setting. 

 (

See “Advanced set up” on page 59 in the CX2032 MFP user’s guide

).  

 

Faxes received sometimes look distorted

 

If the document received is wider or longer than the paper loaded in the paper tray, the 

machine automatically reduces the width or length of the document so that it will fit on the 
paper. This type of problem could also be communication related.

  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MC560 MFP CX2032




























































































Отзывы: