manualshive.com logo in svg

Oki IP-5530, Руководство пользователя

Поделиться
Скачать
Oki IP-5530 Скачать руководство пользователя страница 194

194

Advanced operations

Adjust the heaters temperatures 

Each heater initial value is set in the media preset menu. These values are automatically set for the heaters temperatures. 
 
Therefore, normally the heater control menu is not required. 
The heater control menu is used to: 
  - Complete the temperature fine adjustment during the print operation; or 
  - Confirm the current heater temperature 
 

Procedure to set the heaters temperatures 

(1) The heaters are in standby at the initial 

temperature registered with the media used. 

>>AFTERHEATER T

↕

*50

→

50ºC

 

◎

>>PRINTHEATER T

↕

*40

→

40ºC

 

◎

>>PREHEATER T

↕

*45

→

45ºC

 

◎

When a media type is selected after installing the media, initial temperature 
values of each heater for the selected media type are displayed on the 
menu.

(2) Heating starts after receiving the data from 

the RIP software. 

RIP data

When the heaters temperatures are set with the print and job data from the 
RIP software, the temperatures on the heater control menu are overwritten 
by the temperatures from the RIP. 

  

 

š

To use the initial temperatures set on the operation panel rather than 
the temperature set with the RIP, set HEATER PRIORITY in the media 
preset menu to PANEL SETTING.

(3) When the heaters temperatures have almost 

reached the set temperatures, the print 

operation starts. 

When the current temperatures of the afterheater, printheater, and 
preheater reach a temperature of 1ºC lower than the set temperature, the 
printer starts printing. 

  

 

š

The heaters maximum set temperatures are as follows. 
  Afterheater: 55ºC
  Printheater: 55ºC
  Preheater: 55ºC 

 

š

Even after the print is completed, the temperatures changed during this 
procedure remain as the heaters setup temperatures, until the media is 
installed again or the printer is turned off. 
However, the heater temperature settings in the media preset menu are 
not changed.

(4) Changing the heaters temperatures during the 

print operation. 

↕■■

 45  50 

45ºC

Aft  40 +50 

45Pre

HEATER

During the print operation the heaters temperatures may be changed by 
specifying set temperatures in the heater control menu.

Содержание IP-5530










































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды