Oki B410 Скачать руководство пользователя страница 27

Страница: 27 / 171

43984801TH

Rev.1

27 /

Oki Data CONFIDENTIAL

2. Operational explanation

Fuser unit

Heat roller

DC motor
(Counterclockwise rotation)

Resist roller

Resist clutch

Resist Entrance
sensor lever

Duplex conveying roller

Writing out
sensor lever

Duplex conveying roller

The 1st ejecting roller

The 2nd ejecting
roller

Planet gear

Solenoid
(OFF)

Solenoid
(ON)

[ Normal rotation ]

[ Inverse rotation ]

Belt

Duplex conveying roller

Belt

(4) Paper reversing and paper multi-feeding

1. TRemoving the first eject roller at the rear part of paper and set the solenoid as ON for a while, then the

planet gear starts to move, the second eject roller starts inverse rotating (Counterclockwise rotation).

2. By the inverse rotation of the second eject roller the paper is inversely rotated and conveyed to Duplex.

3. Paper is conveyed by Duplex conveying roller.

4. After setting the entrance sensor lever as ON, paper bumps into the stopped resist roller, still a certain

more amount of paper is conveyed. (This corrects the skew of paper.).

5. If set the Resist clutch as ON, paper is conveyed by Resist roller.

Содержание B410












































































































































































Результаты поиска

Содержание B410

Отзывы:

Бренды по названию

Популярные бренды

Oki B410, Руководство по обслуживанию

Результаты поиска

Содержание B410

Отзывы:

Бренды по названию

Популярные бренды