Oki B410 Скачать руководство пользователя страница 142

Страница: 142 / 171

Appendix A Centronics Parallel Interface

43984801TH Rev.1

142 /

Oki Data CONFIDENTIAL

ACK Width

Narrow

Press the "Menu " key.

ACK/ BUSY Timing

ACK IN BUSY

Press the "Menu " key.

I-PRIME

DISABLE

Press the "Menu " key.

OFFLINE RECEIVE

DISABLE

Press the "Online" key.

Online

The setting is completed.

Items

Output order of BUSY signal and

ACK signal at compatible receiving

Display

Function

ACK IN BUSY

BUSY=LOW is at the posterior border of ACK pulse

ACK WHILE BUSY

BUSY=LOW is at the center of ACK pulse

Factory Default: ACK IN BUSY

Items

I-PRIME

Display

Function

Disable

I-PRIME signal is ignored.

3 microseconds

Enable at the I-PRIME signal of 3μs

50 micro seconds

Enable at the I-PRIME signal of 50μs

Factory Default : 50 Micro seconds (B410 series)
Disable (B420/ B430/ B440 series)

Items

ACK width at compatible receiving

Display

Function

Narrow

0.5μs

Normal

1.0μs

Wide

3.0μs

Default Setting: Narrow

Items

Enable/ Disable of Offline Receiving

Display

Function

Disable

Enable

Enable
I/F signal does not change and still
keep in signal receivable status
even the alarm sounds.

Factory Default: Disable
*It is displayed only when PSE is installed.

Содержание B410












































































































































































Результаты поиска

Содержание B410

Отзывы:

Бренды по названию

Популярные бренды

Oki B410, Руководство по обслуживанию

Результаты поиска

Содержание B410

Отзывы:

Бренды по названию

Популярные бренды