Oilon GP-350 Скачать руководство пользователя страница 21

Страница: 21 / 118

If you set the burner on a pallet, always remove the oil filter.

The burners are attached and supported to a transportation base. The base can be

lifted from all sides with a forklift. When lifting the package, the center of gravity must

be in the middle between the forks to avoid falling.

Use hexagonal key to remove and attach protective covers.

D042848 ver. 2

Pos.

Item

End cover

End cover, fastening screws, 2 pcs

Frame cover (15 kg / 33 lbs)

Frame cover, tightening screw, 1 pcs

Frame cover, fastening screws, 2 pcs

Electric casing protective cover

Electric casing protective cover, fastening screws, 6 pcs

To remove protective covers

1. Loosen the screws of the end cover and remove the cover.

2. Loosen the tightening screw of the frame cover, and also remove its fastening

screws. Draw the cover about 20 mm (0.79 inch) towards yourself and remove it.

3. Loosen the screws of electric casing protective cover, and remove the cover.

4. Reassemble covers in reverse order.

M4248 2316EN

19 (114)

Содержание GP-350























































































































Результаты поиска

Содержание GP-350

Отзывы:

Похожие инструкции для GP-350

Бренды по названию

Популярные бренды

Oilon GP-350, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GP-350

Отзывы:

Похожие инструкции для GP-350

Бренды по названию

Популярные бренды