background image

Mini Merlin Installation, Operation & Maintenance                                                                                                                              

 

Rev: 01 02-22 

16  

Installation Details

 

Please pass this manual to the system owner / user.

 

 

Date of Installation: 

 

Installation Location: 

 

Organisation: 

 

Stamp/Signature of the installer: 

 

 

We recommend all OGS gas detection equipment be commissioned by competent/trained engineers to ensure correct installation 
and operation. The Merlin range of gas detectors are calibrated when manufactured, however, we strongly recommend the 
detectors response and alarm signals are tested and validated once installed. This will ensure the equipment performs as intended 
and is free from any unforeseen damage caused by transit/installation. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Every effort is made to ensure the accuracy of this document; however, OGS can assume no responsibility for any errors or 
omissions in this document or their consequences. OGS would greatly appreciate being informed of any errors or omissions that 
may be found in the content of this document. For information not covered in this document, or if there is a requirement to send 
comments/corrections, please contact OGS using the contact details. 

 
 
 

Oceania Gas Safety 

www.oceaniagassafety.com 

 

Head office: 

Tuakau WaikatoNew Zealand  

 
Tel: 

+64212386990 

Email: 

[email protected]

 

 
 

Oceania Gas Safety is the owner of this document and reserves all rights of modification without prior notice.

 

  

 

Содержание Mini Merlin TFT CH4CO v2

















Отзывы: