Security
Levels
Display Code:
Description:
Adjusting Range:
Set point Value of Control
Alarm 1 Set Point Value. Dwell Time
Ramp Rate
Offset Value for Manual Reset
(Integral Time TI = 0)
Display Shift
Proportional Band of Output 1
Integral (Reset) Time of Output 1
Derivitive (Rate) Time of Output 1
Hysteresis of Alarm 1
Hysteresis of ON-OFF control
Low Scale of Range. Adjust for
your process
High Scale of Range. Adjust for
your process
Power Limit of Output 1
Power Limit of Output 2
Input Type Selection
Display Units
Resolution
Control Action of Output 1
Alarm 1 Mode
Alarm 1 Special Function
Proportional Cycle Time of Output 1
Cooling Cycle Time
Cooling P Band
Dead Band for pB and CPB
Low scale to high scale value. ( , ).
Trip Point within High/Low scale or 0 - 9999 minutes (for Dwell Time)
0 - 99.99
°
F/minute (0 - 55.55
°
C/minute)
0 - 100%
Only functional if Integral is set to 0.
-199
°
to 199
°
F (-111 - 111
°
C) (Refer to page 20)
0 - 360
°
F (0-200.0
°
C)
O: for ON-OFF control (Refer to Page 16)
0 - 3600 seconds
0 - 1000 seconds
0 - 19
°
F (0 - 11
°
C)
0 - 19
°
F (1 - 11
°
C)
0 - 40
Minimum value for the selected Input (INPT) to High Scale (HISC)
Low Scale (LOSC) to maximum value for the selected Input (INPT)
0 - 100%
0 - 100%
= J Type T/C
= E Type T/C
= S Type T/C
= PT100 JIS
0 - 1V
= 1 - 5V
= K Type T/C
= B Type T/C
= N Type T/C
= 4-20 mA
= 0-5V
T Type T/C
R Type T/C
PT100 DIN
= 0-20 mA
0 - 10V
= degree C
= degree F
= process units (Engineering Units)
= No decimal point used
= 2 Digit decimal (only for Linear Voltage or Current Input)
= 1 Digit decimal
= Direct (Cooling) Action
= Reverse (Heating) Action
0
= Deviation High Alarm
= Deviation Band High Alarm
= Full Scale High Alarm
= Deviation Low Alarm
= Deviation Band Low Alarm
= Full Scale Low Alrm
= No Special Function
= Alarm with Hold Function
= Dwell Timer ON as Time Out
= Alarm with Latch Function
= Alarm with Latch & Hold Function
= Dwell Timer OFF as Time Out
0 - 99 Seconds, 0 for Linear current/voltage output
0 - 99 Seconds, 0 for Linear current/voltage output
0 - 360
°
F (0 - 200
°
C)
-199 - 199
°
F (-111 - 111
°
C)
1
2
Default
Setting:
18
°
F
(10
°
C)
0.00
0.0
18
°
F
(10.0
°
C)
120
40
0
0
0
100%
100%
20
For Relay Output
20
For Relay Output
0
=
or
/Minutes
0
0
999
18
°
F
(10.0
°
C)
212
Interface Address
= Proportional Cooling
Press the or key to display set point.
Table 5.3 Index Code (Menu) Descriptions (OPERATOR LEVEL)
Long Scroll
For convenience, parameters can be recorded on the next page.
NOTE: Further parameter definitions on page 15.
