background image

Diff Oil -
Silicone

REQUIRED FOR OPERATION

 

THINGS NEEDED

AA Batteries ( 12 pcs )

Glow Fuel

20%

TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR. 

Phillips Type Screw Drivers ( L )

Phillips Type Screw Drivers  ( S )

Needle Nose Pliers

Cutter

Curved Scissors

Knife

Instant Cement

Cross Wrench
#17109 $3.95

Glow Plug & 17MM Cross Wrench
#10801  $6.95

You need to get batteries for the radio transmitter and the car receiver 
packs.
• Radio TX needs  (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries, Alkaline type batteries will 
work, but braking will be reduced.  The best is to use a 5 cell hump 
pack for increased voltage..

Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 
cell type(600AE).  This will give more run time. OFNA #10212 

#10212 NiHm  Hump Pack,
see charger 10214.

10214

Over-nite

Charger

You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel.  Do not use airplane or heli fuels, they will 
over heat engine.

• Buy SHORT glow plugs,  OFNA/PICCO Plug (#51007) are long 
therefore use two copper washers.  Use plugs without idle bar.  Always 
use two copper washers with Picco glow plugs.

In your box you will find..
• #10163 -  Bottle, spout top or 10162 - Fuel Bottle
• #10218 -  Red “C”  or 10218 Red “D” size glow heater
These parts change depending on stock!

MUST READ THIS BEFORE RUNNING

Running a nitro kit is fun and easy, but to make this a safe 

rusting.
• Clean oil and dirt from chassis with a degreaser.

and good experience you must observe a few rules.  This 
kit is extremely fast, easily over 40MPH, and can seriously 

Precautions

injure someone if you are not careful.

• This kit is not a toy.  Always run car with a second 
person as a spotter and pitman.

Where to run car?

• Any running area you choose must be dry.  Do not run 

• Hot Parts - The pipe, manifold, engine and head are very 

car near any water or wet dirt.

hot and will cause burns.

• Do not run on public streets.  It is very easy to have the 
car run over or damaged by hitting the curb.

• Rotating Parts - Keep hands away from the drive train, 

• Do not operate car in tight confined places. The car is 

wheels, and engine when engine is running.

very fast and will easily hit something.
• Do not run near people or animals. 

• Radio - Check batteries life before running the car.  If 

 

radio does not have full control of the car with steering 

 • Due noise, you will want to consider the surrounding 

and/or throttle/brake do not run until corrected.  Failure to 

area when operating the car.

correct this will result in possible injury and damage to the 

• Do not operate the car at night.  You will not be able to 

car or property.

drive it without hitting something.
• Do not operate the car indoors.  Engine exhaust is not 

• Glow fuel - Do leave the glow fuel unattended with the lid 

healthy.

off.  Fuel contains Methanol and Nitro Methane and is 
flammable and poisonous.

Glow Fuel

• Glow fuel is poisonous!

Store fuel in cool ventilated location.  Refer the glow fuel 

• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time.

label for additional precautions.

• Do not use any fuel other than glow fuel in this engine.

• Car Fuel tank - Never store fuel in car tank, it will ruin the 

First Time Starting the Engine

engine if left in tank.

Caution! When starting engine make sure the following is 
observed.

• Always turn off the car BEFORE turning off radio.

• Set engine Master needle to 3 turns (rich setting)
• Do not do this alone, get an experienced friend to help at 

• DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY 

first.

ISSUE.

• Fill fuel tank, try not to spill fuel.  Do not spill fuel on 
receiver

IF YOU DO NOT BREAK-IN ENGINE 

• Hold car off the ground, so it will not runaway when first 

CORRECTLY, MAINLY AT LOW RPM, 

starts
• Turn on Radio and check the linkage before starting 

YOU WILL BREAK THE CONNECTING 

engine.

ROD!

• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt 
out.

FAILURE TO NOT READ AND 

Engine Break-in

FOLLOW BREAK-IN ENGINE 

• See Engine Page.

Emergency Stopping Engine When Running

INSTRUCTIONS WILL VOID 

• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.

WARRANTY!

• With a rag, cover exhaust outlet.

Storing Car After Running

CHECK RADIO SETTING AND 

• Remove fuel from tank and fuel lines
• Turn off radio in car

LINKAGE BEFORE STARTING

• Put a few drops of after run in engine to keep it from 

The car is very fast 

and will too easily hit someone.

Содержание LD-3 PRO VERSION

































Отзывы: