OfiTE 170-182 Скачать руководство пользователя страница 3

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

2

The OFI Testing Equipment (OFITE) High Temperature High Pressure 

(HTHP) Filter Press is designed to evaluate the filtration characteristics of 

drilling fluids, cement slurries, fracturing fluids, and completion fluids under 

elevated temperatures and pressures. Evaluating fluids under HTHP condi

-

tions similar to the downhole environment is of paramount importance. Fluid 

properties must be monitored while under high temperatures and pressures 

as filtration behavior and wall cake building characteristics of permeable 

formations change with changing environments. These characteristics are 

affected by the shape, type, and quantities of solids present in the fluid and 

their physical and electro-chemical interactions, all of which are affected by 

changing temperatures and pressures.

OFITE manufactures and provides HTHP filtration units in two basic sizes, 

175 mL and 500 mL capacities. Both are used extensively throughout the 

world and in all environments, but in general the 175 mL units are designed 

for field portability, while the larger 500 mL units are designed for laboratory 

usage at higher temperatures and pressures. All OFITE Filtration devices fully 

conform to American Petroleum Institute (API) specifications.

A complete HTHP Filter Press consists of a controlled pressure source, usu

-

ally Nitrogen pressurization or Carbon Dioxide bulbs for the 175 mL units. 

Top and bottom pressure manifolds are provided to simulate the differential 

pressures found in a down-hole environment, and to prevent evaporation 

of the base fluid if exceeding the boiling point of that fluid. The test cells are 

provided in a variety of assemblies, depending upon the type of fluid tested, 

the filter media, and the temperatures and pressures desired. The test cells 

are encased inside a heating jacket, which is adjustable.

A variety of filter media are available, the most common being standard API 

filter paper, cement screens, and ceramic filters. The ceramic filters may be 

obtained to match the pore throat or permeability of the formation. Natural for

-

mation filters or cores may also be used of differing pore throat / permeability 

sizes. Slotted disks of varying sizes are frequently used for lost circulation 

materials studies.

Both the 175 mL and the 500 mL heating jackets are capable of reach

-

ing 400°F (204°C), but lower fluid volumes due to fluid expansion at higher 

temperatures, limit the 175 mL units to a useful working temperature of 300°F 

(149°C). Anyone running tests above 350°F (177°C) must substitute a com

-

plete set of o-rings after each and every test.

Intro

Содержание 170-182




























Отзывы: