3
Operating Instructions and Parts Manual
24850
11/17
2017 OEMTOOLS
™
20 TON
AIR/HYDRAULIC JACK
28. For safety purposes and the prevention of damage to
expensive components, it is advised that the user have
an understanding of basic automotive repair and a
working knowledge of automotive systems.
29. We believe the information contained herein to be
reliable. However, general technical information
is given by us without charge and the user shall
employ such information at their own discretion
and risk. We assume no responsibility for results or
damages incurred from the use of such information
in whole or in part. Always refer to specific
instructions and technical information supplied by
vehicle manufacturer.
30. The manufacturer declines any and all responsibility
for damage to vehicles or components if said damage
is the result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
31. This equipment is intended only for professional use by
personnel trained in performing the service functions
for which it has been designed.
32. This equipment is designed for servicing a variety
of vehicles in a safe, convenient manner. However,
differences in vehicle makes and models may make
it impossible to use this equipment as it is intended.
DO NOT attempt to force the use of this equipment
on an application for which it is not designed to
perform.
33. The procedures documented in this manual are to
serve as guidelines for the use of this equipment.
34. In addition to these guidelines, always follow the
manufacturer’s recommended procedures when
servicing each unique vehicle.
35. The use of this equipment is simple and
straightforward if you follow the instructions. When
operating this equipment, use common sense, and
always stop to think before using a Jack or lifting a
vehicle
PRODUCT SPECIFICATIONS
Capacity:
20 Ton
Min. Height:
9.5" Min.
Ram Travel:
6.25"
Screw Adj.:
3.25"
Max. Height:
15.5"
Air Pressure:
110-125 PSI
Air Inlet Fitting:
1/4" NPT
PRODUCT DESCRIPTION
The heavy-duty OEMTOOLS
™
20-Ton Air/Hydraulic Jack
has a powerful air motor to lift heavy loads with ease.
The compact design easily fits between dual tandem
axles. This jack is great for lifting axles, farm vehicles,
heavy-duty machinery, and industrial construction
equipment.
NEVER
use for any purpose other than the uses outlined
above!
1. Verify that the product and application are compatible,
if in doubt call OEMTOOLS
™
at 1-866-458-2472.
2. Before using this product, read the operator’s
manual completely and familiarize yourself
thoroughly with the product, its components and
recognize the hazards associated with its use.
3. Wear appropriate safety gear, including heavy-duty
work gloves and ANSI-approved safety goggles
during use.
4. Ensure that jack rolls freely. Raise and lower the
unloaded jack throughout the lifting range before
putting into service to ensure the pump operates
smoothly. Replace worn or damaged parts.
5. DO NOT exceed the weight capacity of the jack. Make
sure weight is evenly distributed. Be aware of dynamic
loading! Sudden load movement may briefly create
excess load causing product failure. Exceeding the
maximum capacity for this product is dangerous and
can lead to serious injury or property damage.
6. Always evaluate your task before using this jack. Jacks
are designed to lift, but not support, rated capacity
partial vehicle loads consisting of one end of a vehicle.
Immediately after lifting, support loads with a pair of
appropriately rated jack stands. Use only as intended.
7. Use only on a hard, level and flat surface capable of
bearing the combined weight of the Jack, the load
being lifted, the operator and any tools being used.
8. If you are working and the load becomes off-balance
and/or the jack begins to tip over, DO NOT ATTEMPT
TO CATCH OR LIFT THE LOAD WHEN FALLING. SERIOUS
PERSONAL INJURY CAN RESULT! In this event, clear
the area as quickly and safely as possible in order to
avoid injury from the falling load, including getting hit
with flying fragments.
9. Before each use, inspect the general condition of
the Jack. Check for oil leaks, jack operation, loose
components, free rotation and pivoting of saddle
adjustment components. If a problem occurs, have the
problem corrected before further use.
Содержание 24850
Страница 8: ......
