2
Operating Instructions and Parts Manual
24482
HEAVY DUTY 1/2” 2VSR
CORDLESS 20V LI-ION DRILL
10/15
2015 OEMTOOLS
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as, potential hazards specific
to it.
2. Keep work area clean and well lit. Cluttered or dark work areas
invite accidents.
3. Keep children away. All children should be kept away from the work
area. Never let a child handle a tool without strict adult supervision.
4. Do not operate this tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment
or reflexes are impaired while taking drugs. If there is any doubt, do
not attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid
safety shoes, hard hat or hearing protection should be used in
appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. Don’t overreach. Keep proper footing and balance at all times when
operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged it should be carefully inspected to make sure that it can
perform its intended function correctly. If in doubt, the part should
be repaired. Refer all servicing to a qualified technician. Consult
your dealer for advice.
9. Keep away from flammables. Do not attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained persons.
Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
14. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
15. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
result in a risk of injury.
16. When servicing a tool, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions may
create a risk of injury.
17. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the work
area free of obstructions, grease, oil, trash, and other debris. Do not
use this product in a damp or wet location.
18. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact OEMTOOLS
for a replacement.
19. Before use, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe
the correct procedure and test data for each vehicle.
20. Always perform vehicle service in a properly ventilated area. Never
run an engine without proper ventilation for its exhaust. Stop work
and take necessary steps to improve ventilation in the work area
if you develop momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
WARNING
Read Rules for Safe Operation and Instructions Carefully.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur.
The operator must understand that common sense and caution are
factors which cannot be built into this product, but must be supplied
by the operator.
DISPOSAL
At the end of the useful life of the OEMTOOLS Drill, dispose of the
components according to all state, federal, and local regulations.
BATTERY DISPOSAL
Exposure to high temperatures can cause the batteries to explode; do
not dispose of in a fire. Some countries have regulations concerning
battery disposal. Follow all applicable regulations. Return used batteries
to a collection location for recycling.
PURPOSE
The OEMTOOLS Heavy Duty 1/2” 2VSR Cordless 20V Li-Ion Drill is used
for drilling holes, driving screws, loosening or tightening various materials
together with fasteners and other applications.
PRODUCT SPECIFICATIONS
Chuck Size:
1/2"
2 Speed Gear Box:
0-600 RPM and 0-2,000 RPM
Weight:
7 Lbs.
Charge Time:
1 Hour
Clutch:
21 + 1 Torque Clutch Setting
Includes:
Lithium-Ion Battery with Charging Station
and Chuck
INSTRUCTIONS:
Always wear safety goggles and gloves.
DRILLING
1. If drilling in a small work piece, make sure it is securely held in a vise
or clamped to a secure platform such as a bench or table.
2. Install the correct drill bit in the chuck. Rotate the chuck body to
loosen or tighten the drill bit in the chuck. Never use the drill’s power
to rotate the chuck body.
3. Select the rotation direction to clockwise using the button located
above the trigger switch.
