background image

13

ODB COMPANY

   800-446-9823       

 

LCT60C

SAFETY PRECAUTIONS

Improper use of the ODB leaf collector CAN result in severe per-

sonal injury or death.  All personnel using this leaf vacuum must 

be trained and qualified with all the operations, maintenance, repair 

and safety procedures defined in this manual.

1.3 Training:

The warnings and procedures regarding safety in this manual are to be 

used as a guideline only.  It is impossible to cover all the events that could 

happen in the vacuuming process.   For this reason, it is vital that the 

owner accept the responsibility to implement a training program that will 

provide every operator or mechanic the basic skills and knowledge to make 

good judgement in all situations.

This training program must include the entire scope of hazards, precautions 

and government regulations encountered in the vacuuming process.    The 

program should stress the need for regularly scheduled preventive mainte-

nance and detailed equipment safety checks.

It is strongly recommended that all training programs be documented to 

ensure all operators and mechanics receive initial training on not just the 

operation but the safety features of the leaf collector.   

 

  

Содержание LCT60C

















































































































Отзывы: