Octek BISON II Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 57

background image

RADIO FREQUENCY INTERFERENCE
STATEMENT

This equipment generates and uses radio frequency
energy and if not installed and used properly, that
is, in strict accordance with the manufacturer's
instructions, may cause interference with radio and
television reception.

If this equipment does cause interference to radio
or TV reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

*

Reorient the receiving antenna.

*

Relocate the computer away from the receiver.

*

Move the computer away from the receiver.

*

Plug the computer into a different outlet so that

computer and receiver are on different branch
circuits.
*

Ensure that card slot covers are in place when

no card is installed.
*

Ensure that card mounting screws, attachment

connector screws, and ground wires are tightly
secured.
*

If peripherals are used with this system, it is

suggested to use shielded, grounded cables, with
in-line filters if necessary.

If necessary, the user should consult the dealer
service representative for additional suggestions.

The manufacturer is not responsible for any radio or
TV interference caused by unauthorized
modifications to this equipment. It is the
responsibility of the user to correct such
interference.

«
1
2
3
4
5
...
»

Содержание BISON II


























































Отзывы:

Нет отзывов

Похожие инструкции для BISON II

Бренд: MSI Страницы: 94

Бренд: MSI Страницы: 76

Бренд: BIGTREETECH Страницы: 39

Бренд: Gan Systems Страницы: 28

FEBFL7701_L31H008A

Бренд: Fairchild Страницы: 24

E-Vision Electric Thruster E300

Бренд: Sleipner Страницы: 28

Бренд: IBASE Technology Страницы: 84

CLICKER 4 for STM32

Бренд: Mikroe Страницы: 16

Бренд: Supermicro Страницы: 142

AR0832MBSC25SUFAH-GEVB

Бренд: ON Semiconductor Страницы: 6

Бренд: Unicorn Computer Страницы: 36

KEMX-1600 Series

Бренд: Quanmax Страницы: 74

Бренд: Intel Страницы: 76

NB-IoT Module Series

Бренд: Quectel Страницы: 31

Бренд: BCM Страницы: 57

B560 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: C&T Solution Страницы: 90

Бренд: Rosch Computer Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды