background image

 

Document UT-MT-0708_EN 

Page 7 of 17 

 

Edition 11/03/2014 

Supersedes edition 11/14/2013 

LED ELEVATED HELIPORT LIGHT LHE 
INSTRUCTION MANUAL FOR USE, INSTALLATION AND MAINTENANCE 

 

1

 

GENERAL 

LHE 

elevated LED heliports light is low intensity, omnidirectional steady burning type. 

These fixtures are intended for use as helipad area lighting. 

LHE  lights  are  in  compliance  with  ICAO  Annex  14  Vol.2,  IEC  TS  61827  and  NATO-
STANAG 3619. 

The  fixtures  described  in  this  manual  are  designed  to  be  connected  to  parallel 
circuits. 

Location  of  these  fittings  shall  be  in  compliance  with  ICAO  -  Annex  14  or  STANAG 
Specs 

2

 

MAIN FEATURES 

The fixture consists of: 

 

heat  resistant  transparent  glass  lens;  it  is  mechanically  secured  to  the  body  by 
metal threaded ring with flat gasket 

 

aluminium body mounted on the pole using three screws. These screws also allow 
the levelling of equipment 

 

the power supply/control PCB and the LED circuit are mounted on the aluminium 
inner body 

 

steel  1-inch-tube,  available  in  different  length,  connecting  the  main  body  and 
fragile joint; to lock the tube, the breakable coupling is equipped with one screw 

 

aluminium breakable coupling provided with a breakable groove 2" GAS 

 

two,  single-pole  neoprene  cable  leads,  size  2.5  mm2,  0.3  m  long,  with  plug 
meeting  FAA  Specs  L-823;  a  yellow-green  wire,  size  2.5  mm2,  0.5  m  long,  is 
provided  for  grounding  purpose;  as  alternative  a  cable  lead  (L  =  2  m  exceeding 
over the breakable coupling) can be provided 

 

a LED module, consisting of six LED, mounted on a PCB complete with a dedicated 
optic to collect the LED luminous flux so to maximize the light output 

All hardware is made of stainless steel. 

See 

“Complete P/N identification”

 figure for P/N information. 

Power consumption 28 VA and 11 VA (white or green/yellow respectively). 

Содержание LHE


















Отзывы: