Oce VarioPrint 6000 Plus Line Скачать руководство пользователя страница 34

Страница: 34 / 102

Lock the clean unit (left)

Introduction

This procedure is only intended for key operators who received the special maintenance training.

When to do

After you replaced the cleaners

Replace the cleaners on page 14

, you must restart the machine. If

you accidentally forgot to lock a clean unit after you replaced the cleaners, the machine will
detect this during the initialization. Then the operator panel will display this maintenance task.

Required tools

Service key (supplied with the machine)

Socket wrench 10 (supplied with the machine)

Procedure

Press [Start] to start the maintenance wizard.
At the start of the procedure, the machine is turned off.

CAUTION

Wait until the machine is turned off. Opening the doors too soon can possibly cause
injury.

Use socket wrench 10 to loosen the bolt of the front doors (2).

Open the front doors (3).

[32] Open the front doors

Lock the clean unit (left)

Chapter 2 - Maintenance tasks - Level 1

Océ VarioPrint 6000 line

Содержание VarioPrint 6000 Plus Line







































































































Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды

Oce VarioPrint 6000 Plus Line, Руководство по обслуживанию

Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды