background image

Copyright Information

Copyright © 2007 - 2013 by Obvius

Obvius

,

 AcquiSuite and ModHopper 

are trademarks of  Obvius Holdings LLC

Other brand and product names are trademarks or registered trademarks of their respective holders. 

U.S. Government Restricted Rights: 

Use, duplication or disclosure by the Government is subject to restrictions set fourth in subparagraph (a) through 

(d) of the Commercial Computer Restricted Rights clause at FAR 52.227-19 when applicable, or subparagraph (c) (1) (ii) of the Rights in Technical Data 
and Computer Software clause at DFARS 252.227-7013, and in similar clauses in the NASA FAR Supplement.

Limited Warranty

OBVIUS IS PROVIDING THIS WARRANTY IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY WARRANTY 
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY IS BUYER'S EXCLUSIVE REMEDY FOR ALL 
CLAIMS AGAINST OBVIUS. OBVIUS SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES. OBVIUS'S TOTAL 
LIABILITY FOR ALL CLAIMS SHALL BE LIMITED TO THE PRICE PAID FOR ITS PRODUCT.

Obvius promises buyer that any standard product manufactured by Obvius shall be free from all material defects in design, material, or manufacturing for 
a period of 2 years from the manufacture date; provided, however, that the warranty shall not extend to ordinary wear and tear or to normally replaceable 
components (e.g., batteries). During the warranty period, Obvius may repair or replace (in its sole discretion) any product suffering from a warranty defect 
and returned freight prepaid by buyer, with no charge to buyer for any warranty repair or replacement. The warranty shall remain in full force and effect 
for such 2 year period, provided that the product: (1) was installed, operated, and maintained properly; (2) has not been abused or misused; (3) has not 
been repaired, altered, or modified outside of Obvius's authorized facilities; (4) has not been sold subject to other warranty terms specified at the time of 
sale; and (5) is still owned by the original purchaser. This warranty provides specific legal rights that may be varied by state law. Obvius's products are not 
designed for life or safety applications.

Product Application Limitation

Obvius strongly believes in continuous improvement, therefore we must reserve the right to change specifications and product offerings without notice. 
Where possible, we will substitute products with equivalent functionality when necessary.

 

DANGER 

 

Hazard of Electric Shock, Explosion or Arc Flash

Follow safe electrical work practices.  See NFPA 70E in the USA, or applicable local codes. 

This equipment must only be installed and serviced by qualified electrical personnel.

Read, understand and follow the instructions before installing this product.

Turn off all power supplying equipment before working on or inside the equipment.  Use properly rated voltage sensing device to 
confirm power is off.   DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

Only install this product on insulated conductors. 

Failure to follow these instructions will result in death or serious injury.

NOTICE

This product is not intended for life safety applications. 

Do not install this product in hazardous or classified locations.

The installer is responsible for conformance to all applicable codes.

Mount this product inside a suitable fire and electrical enclosure.

FCC Part 15 Information

Note: This equipment has been tested by the manufacturer and found to comply with the limits of a class A digital device, pursuant to part 
15 of the FCC rules.  These limits are designed to provide reasonable protection against interference when the equipment is operated in a 
commercial environment.  This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications.  Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.  
Modifications of this product without the express authorization of Obvius nullify this statement.

Page 2

A90DC-12 – DC Current Monitor

www.

.com

[email protected]

1.800.561.8187

Содержание A90DC-10
















Отзывы: