background image

zImage

The Linux operating system.

When clicking on the Upgrade button, the AcquiSuite will again download the requested firmware image file. The 
AcquiSuite will take a few seconds to verify the file checksum and prompt you with an “Install” button. Click the install 
button and the AcquiSuite will install the firmware update and reboot itself to make the changes take effect.  

Do not power down the AcquiSuite during any step of the AcquiSuite firmware update process.  Doing so may corrupt the 
system and render the AcquiSuite unusable. 

Diagnostics 

Host Lookup

The Host Lookup page provides the ability to do some basic network tests.  These are as follows:

Ping

: send an echo request to the specified host.

Traceroute

: Send an echo request to the target address and attempt to locate every router in between the AcquiSuite and 

that address.

Nslookup

: convert the dns name to an IP address, useful for testing the functionality of the DNS server configured in the 

Network/Setup webpage.

To run a network test, enter the ip address or dns name in the field provided, check the checkbox next to the test you wish to 
use, and click the OK button.  Multiple tests can be specified. 

Connection Test

The connection test page will attempt to establish an HTTP session with the specified upload server.   Click the “begin test” 
to start this process.  Information will be printed in black.  Success responses will be printed in Green, failure messages will 
be printed in Red.   A sample upload test follows:

Ping localhost [127.0.0.1]: 

Success

Ethernet IP address [192.168.10.50], mask [255.255.255.0]

Local subnet [192.168.10.0] to [192.168.10.255]

Ping ethernet ip address [192.168.10.50]: 

Success

Starting system debug logger

Dialout not enabled, using ethernet LAN connection.

Ping ethernet gateway [192.168.10.1]: 

Success

Ping DNS #1 [192.168.10.1]: 

Success

The DNS #2 server address is not configured.

Resolving time server [time.obvius.com] to an IP address: 

Success. Got [70.99.203.62]

Ping time server [time.obvius.com]: 

Success

Testing time server

SyncTime: Sync system time with time.obvius.com.

   16 Dec 19:49:36 ntpdate[3165]: adjust time server 70.99.203.62 offset 0.009985 sec

   new time: Tuesday, December 16 2003 19:49:36 PST, drift 1 seconds.

Processing upload url.

No proxy specified, using direct connect method.

Upload URL looks ok: 

http://www.buildingmanageronline.com/upload.php

Resolving web server [www.buildingmanageronline.com] to an IP address: 

Success. Got 

[70.99.203.62.56.37]

Ping web server [www.buildingmanageronline.com]: 

Success

Connecting to server at [70.99.203.62:80]: 

Success 

Sending HTTP request: 

Success 

Reading response:

Upload test completed.

  Got:

  HTTP/1.1 200 OK

  Date: Wed, 17 Dec 2003 03:49:38 GMT

  Server: Apache/1.3.23 (Unix) PHP/4.1.2 AuthMySQL/2.20

X-Powered-By: PHP/4.1.2

Connection: close

Content-Type: text/html

  SUCCESS - Test Successful

Closing TCP connection

Shutting down system debug logger

Test complete

Page 22

A8810 AcquiSuite – Data Acquisition Server

www.

.com

[email protected]

1.800.561.8187

Содержание A8810-GSM































Отзывы: