Oakley TM3030 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 22

Oakley TM3030 Скачать руководство пользователя страница 22

Final Comments

If you have any problems with the module, an excellent source of support is the Oakley Sound
Forum at Muffwiggler.com. Paul Darlow and I are on this group, as well as many other users
and builders of Oakley modules.

If you can't get your project to work, then Oakley Sound Systems are able to offer a 'get you
working' service. If you wish to take up this service please e-mail me, Tony Allgood, at my
contact e-mail address found on the website. I can service either fully populated PCBs or
whole modules. You will be charged for all postage costs, any parts used and my time at
25GBP per hour. Most faults can be found and fixed within one hour, and I normally return
modules within a week. The minimum charge is 25GBP plus return postage costs.

If you have a comment about this user guide, or have a found a mistake in it, then please do let
me know. But please do not contact me directly with questions about sourcing components or
general fault finding. Honestly, I would love to help but I do not have the time to help
everyone individually by e-mail. Questions are always best directed to the Oakley Sound
Forum.

Tony Allgood at Oakley Sound

Cumbria, UK
© May 2014 – Updated May 2017

22

«
...
20
21
22

Содержание TM3030























Отзывы:

Нет отзывов