Oakley TM3030 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 22

Oakley TM3030 Скачать руководство пользователя страница 2

Introduction

This is the Builder’s Guide for the issue 3 TM3030 sound module from Oakley Sound. This
document contains a basic introduction to the board, a full parts list for the components
needed to populate the board or boards, and a list of the various interconnections,

For the User Manual which contains an overview of the operation of the unit and the
calibration procedure please visit the main project webpage at:

http://www.oakleysound.com/tm3030.htm

For general information regarding where to get parts and suggested part numbers please see
our useful Parts Guide at the project webpage or http://www.oakleysound.com/parts.pdf.

For general information on how to build our modules, including circuit board population,
mounting front panel components and making up board interconnects please see our generic
Construction Guide at the project webpage or http://www.oakleysound.com/construct.pdf.

An issue 2 board awaiting its case and LEDs. This one has been built with a matched BC550B pair in the

VCF and a CA3080 and discrete buffer for the VCA. Issue 3 is almost identical.

2

«
1
2
3
4
...
»

Содержание TM3030























Отзывы:

Нет отзывов