O.S. engine OSM11532 Скачать руководство пользователя | Manualshive

Страница: 26 / 38

background image

CARBURETTOR AIR-BLEED ADJUSTMENT

Start engine and adjust needle-
valve as previously described.

Close the throttle gradually.

Find the idling position.

approx.
15˚

Hold the model.

Hold model level, then slowly raise its nose.

If revolutions increase.

If engine runs unevenly or stops.

approx.
15˚

Immediately point
nose down, so that
engine runs steadily
again.

Stop the engine.

Stop the engine.

Note: Stop engine by
pinching fuel delivery
tube. Do not touch
needle-valve.

Open air-bleed
screw.

Half turn at a
time.

Close air-bleed
screw.

Half turn at a
time.

Pre-Flight Check

Repeat the procedure while opening and closing

the throttle until the best result is obtained.

Attention: Do not leave the glowplug connected to the battery

while adjusting the carburettor throttle.

These adjustments can be
made without stopping
the engine.
However, it is advisable for
beginners to stop the engine
for safety reasons.

25

«
...
24
25
26
27
28
...
»

Содержание OSM11532







































Отзывы:

Нет отзывов

Похожие инструкции для OSM11532

Бренд: Mitsubishi Страницы: 176

E-II SGM H Series

Бренд: YASKAWA Страницы: 408

Бренд: Scania Страницы: 83

Бренд: TYROLIT Hydrostress Страницы: 19

Бренд: IEF Werner Страницы: 38

Бренд: nord Страницы: 91

Бренд: Caple Страницы: 16

Бренд: Volvo Penta Страницы: 132

Бренд: Lycoming Страницы: 120

Бренд: Yanmar Страницы: 182

Бренд: Vanguard Страницы: 124

Бренд: Coleman Страницы: 79

Бренд: Lister Petter Страницы: 88

GX 610 standard

Бренд: Honda Страницы: 69

Бренд: Steyer Motors Страницы: 174

Бренд: Mitsubishi Страницы: 364

Бренд: Ford Страницы: 11

Бренд: Packard Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды