background image

A

B

75%

20%

5%

65%

20%

15%

Methanol

Castor Oil

Nitromethane

Model engine fuel is poisonous. Do not 
allow it to come into contact with the eyes or 
mouth. Always store it in a clearly marked 
container and out of the reach of children.

Model engine fuel is also highly flammable. 
Keep it away from naked flame, excessive 
heat, sources of sparks, or anything else 
which might ignite it. Do not smoke, or allow 
anyone else to smoke, near to it.

Reminder!

7

4

8

4

9

5

10LA

15LA

25LA

7

3

~

5,8

4

7

5

~

6,8

4

~

5

9

5

~

6

PROPELLER
Suggested propeller sizes are given in the table. As 
the ideal propeller diameter, pitch and blade area vary 
according to the size, weight and type of model, final 
propeller selection can be made after practical 
experiment.

Trainer & Sport

LA Series

Never touch, or allow any object to come 
into contact with, the rotating propeller and 
do not crouch over the engine when it is 
running.

Running-in

Reminder!

GLOWPLUG
An O.S. A3 glowplug is fitted to the engine. 
Other recommended O.S. plugs are Nos.8 and A5. 
Carefully fit plug finger-tight, before final tightening 
with the correct size plug wrench.

The role of the glowplug

With a glowplug engine, ignition is initiated by the 
application of a 1.5-volt power source. When the battery 
is disconnected, the heat retained within the combustion 
chamber remains sufficient to keep the plug filament 
glowing, thereby continuing to keep the engine running. 
Ignition timing is 'automatic' : under reduced load, 
allowing higher rpm, the plug becomes hotter and, 
appropriately, fires the fuel/air charge earlier; 
conversely, at reduced rpm, the plug become cooler and 
ignition is retarded.

13

Содержание OSM11532







































Отзывы: