background image

It  is  of  vital  importance,  before  attempting  to 
operate  your  engine,    to  read  the  general 

'SAFETY  INSTRUCTIONS  AND  WARNINGS' 

section  on  pages  2-4  of  this  booklet  and  to 
strictly adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction  manual,  so  as  to  familiarize 
yourself with the controls and other features of 
the engine.
Keep these instructions in a safe place so that 
you  may  readily  refer  to  them  whenever 
necessary.
It is suggested that any instructions supplied 
with the aircraft, radio control equipment, etc., 
are accessible for checking at the same time.

1

CONTENTS

 

15

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

INTRODUCTION, BASIC ENGINE PARTS

INSTALLATION

THROTTLE LINKAGE,
INSTALLATION OF SILENCER (MUFFLER)

FUEL TANK LOCATION, GLOWPLUGS

FUEL, PROPELLER

MIXTURE CONTROLS, STARTING

RUNNING-IN ("Breaking-in")

MIXTURE CONTROL ADJUSTMENT CHART

SUBSEQUENT READJUSTMENT,
CARBURETOR CLEANLINESS.
ENGINE CARE AND MAINTENANCE

ENGINE EXPLODED VIEW & PARTS LIST 

CARBURETOR EXPLODED VIEWS &
PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

MEMO

MIXTURE CONTROL VALVE ADJUSTMENT,
REALIGNMENT OF MIXTURE CONTROL VALVE,
SUBSEQUENT STARTING PROCEDURE

14

2-4

5

6

7

8

9

10

11-12

13

16

17

18

19

20

Содержание Max-BGX-1 Ring












Отзывы: