background image

14

FACTS ABOUT GLOWPLUGS

The role of the glowplug

Glowplug life

Particularly in the case of very high performance 
engines, glowplugs must be regarded as expendable 
items. 

With a glowplug engine, ignition is initiated by the 
application of a 1.5-volt power source. When the 
battery is disconnected, the heat retained within the 
combustion chamber remains sufficient to keep the 
plug filament glowing, thereby continuing to keep the 
engine running. Ignition timing is 'automatic' : under 
reduced load, allowing higher rpm, the plug becomes 
hotter and, appropriately, fires the fuel/air charge 
earlier; conversely, at reduced rpm, the plug become 
cooler and ignition is retarded.

Since the compatibility of glowplug and fuel may have 
a marked effect on performance and reliability, it may 
be worthwhile to choose the R/C type plug found 
most suitable after tests. Recommended O.S. plugs 
are No.8, A5 and A3. Carefully install plug finger-tight, 
before final tightening with the correct size plug 
wrench.

Install a plug suitable for the engine.

Use fuel containing a moderate percentage of 
nitromethane. 

Do not run the engine too lean and do not leave the 
battery connected while adjusting the needle. 

However, plug life can be extended and engine 
performance maintained by careful use, i.e.:

Apart from when actually burned out, a plug may 
need to be replaced because it no longer delivers its 
best performance, such as when:

When to replace the glowplug

Filament surface has roughened and turned white. 

Filament coil has become distorted.

Foreign matter has adhered to filament or plug 

body has corroded.

Engine tends to cut out when idling.

Starting qualities deteriorate.

15

INSTALLING
THE GLOWPLUG

Install washer on glowplug and insert carefully into 
Heatsink-head, making sure that it is not cross-
threaded before tightening firmly. 

Glow plug

Washer

INSTALLATION OF THE ENGINE

The under-surfaces of all O.S. engine beam 
mounting lugs are precision machined flat and 
exactyly parallel to the engine's horizontal axis. It is 
essential that the engine mounts in the model are 
also accurately made and aligned. If they are not, 
they will cause stress and distortion within the engine 
itself, probably resulting in loss of performance and 
internal damage. The recommended screws for 
securing the engine to the engine mounts in the 
model are 3mm or 4-40 steel Allen type. It is also 
advisable to use lock washers or LOCTITE to prevent 
nuts from loosening.

With some models, needle interferes the body 

and working on the body to avoid this would be 

required.

NOTE:

Содержание MaX-37SZ-HRING






















Отзывы: