O.S. engine MAX-21VZ-R страница 10 Скачать руководство пользователя

Страница: 10 / 23

LONG SOCKET WRENCH

Recommended for easy removal
and replacement of the angled
and recessed glowplug, the
O.S.Long Socket Wrench
incorporates a special grip.

SILICONE FUEL LINE

Heatproof silicone tubing of
approx. 5mm o.d. and 2mm i.d.
is required for the connection
between the fuel tank and
engine.

CARBURETOR CONTROLS

The Needle-Valve:

•

The Mixture Control Screw:

•

The Throttle Stop Screw:

For setting the minimum idling speed:

•

Four adjustable controls are provided on this
carburettor.

For adjusting the mixture strength when the throttle
is fully open.

For adjusting the mixture strength at part-throttle
and idling speeds, to obtain steady idling and
smooth acceleration to mid speeds.

Needle Valve

Mixture Control Valve
Assembly Screw

Throttle Stop Screw

NOTE: Readjustment may be necessary,
occasionally to allow for changes in fuel formula
gear ratio or clutch engagement point.

The Metering Needle:

•

Metering Needle

For changing the feeling at mid speads and
acceleration. (Do not rotate the screw more chan
one turn.)

Содержание MAX-21VZ-R
























Результаты поиска

Содержание MAX-21VZ-R

Отзывы:

Похожие инструкции для MAX-21VZ-R

Бренды по названию

Популярные бренды

O.S. engine MAX-21VZ-R, Инструкция пользователя

Результаты поиска

Содержание MAX-21VZ-R

Отзывы:

Похожие инструкции для MAX-21VZ-R

Бренды по названию

Популярные бренды