background image

Do not apply the starter to a flooded engine and 
never place your finger over the carburettor in-
take when using the starter. This may cause an 
hydraulic lock and bend the connecting-rod.

To stop the engine, fully close the throttle to cut off 
air supply. 

Warning:

In case of the 21RG-MX 

Take the same procedure as 
the 21RG-M to the point of 
"Heat the glowplug by 
connecting the battery 
leads".

Pull the starter handle 
briskly straight out several 
times to start the engine.

Starter Handle

Heat the glowplug by connecting the battery leads.
Make sure that the direction of rotation of the 
electric starter is correct, namely, clockwise. 

If necessary, reverse leads on battery to provide 
clockwise rotation.

Hang the starter belt over the flywheel and starter 
and depress the starter switch for one or two 
seconds. Repeat if necessary. When the engine 
fires, withdraw the starter immediately.

PRECAUTIONS
When starting the engine, 
the hull is off the water and 
the engine is run with no 
load, and with even below 
half throttle engine r.p.m. 
come high.  Prolonged 
running with this condition may result in the 
seizure of the connecting rod and crank pin.  
Never run the engine with high r.p.m. (never open 
the throttle beyond the starting setting) with no 
load (i.e. the hull is off the water).

14

Содержание max-21RG-M































Отзывы: