NXP Semiconductors SSL2108X Скачать руководство пользователя страница 3

UM10468

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 1 — 30 August 2011 

3 of 27

NXP Semiconductors

UM10468

SSL2108X buck evaluation board

1. Introduction

The SSL2108X is a family of high-voltage Integrated Circuits (IC), designed to drive 
non-dimmable retrofit LED lamps in general lighting applications. The product family 
consists of four ICs with different configurations which are shown in 

Table 1

.

 

[1]

SO12 package variants have more fused leads for lower thermal resistance and can be used when a higher 
output power is needed.

Main benefits of the product family are:

Small Printed-Circuit Board (PCB) footprint providing a compact solution

High-efficiency (up to 95 %)

Ease of integration

Low electronic Bill Of Material (BOM)

The SSL2108X provides accurate output control with more than 5 % LED current 
accuracy. The ICs can operate using Pulse-Width Modulation (PWM) dimming and have 
many protection features including easy external temperature feedback.

The SSL2108X driver family is the high performance solution for the next generation of 
retrofit LED lamps. These ICs provide a high efficiency, high-power factor solution in a 
small form factor.

Remark: 

Unless otherwise stated all voltages are in V (DC).

WARNING

Lethal voltage and fire ignition hazard

The non-insulated high voltages that are present when operating this product, constitute a 
risk of electric shock, personal injury, death and/or ignition of fire. 

This product is intended for evaluation purposes only. It shall be operated in a designated test 
area by personnel qualified according to local requirements and labor laws to work with 
non-insulated mains voltages and high-voltage circuits. This product shall never be operated 
unattended.

Table 1.

SSL2108X type number overview

Type

Package

V

mains

 range 

(V (AC))

Internal MOSFET 
characteristics

Adjustable brownout 
protection

SSL21081

SO8

100 to 120

300 V; 2

no

SSL21082

SO12

[1]

yes

SSL21083

SO8

100 to 230

600 V; 5

no

SSL21084

SO12

[1]

yes

Содержание SSL2108X




























Отзывы: