NXP Semiconductors S32R27 Скачать руководство пользователя | Manualshive

Страница: 48 / 50

background image

Table 35. S32R family miscellaneous connections (continued)

FCCU External Error Signal -
FCCU_F0

R17

R17

L13

The Fault Collection and Control Unit (FCCU) has
error output signals for the communication of errors to
external devices. The use of these signals is
application specific, more information can be found in
the FCCU chapter in the device reference manual.

FCCU External Error Signal -
FCCU_F1

M14

M14

K11

The Fault Collection and Control Unit (FCCU) has
error output signals for the communication of errors to
external devices. The use of these signals is
application specific, more information can be found in
the FCCU chapter in the device reference manual.

Non-Maskable Interrupt (NMI)

N16

N16

K13

NMI input can be found on pin N16. The use of this
pin is application specific; please see the Wake-up
Unit (WKPU) chapter in the device reference manual
for more information.

If the pin is not used, it can be rendered non-
functional by connecting to VDD_HV_IO through a
4.7 Kilo Ohm or 10 Kilo Ohm pull-up resistor.

No Connect Strategy

J1, J2,
K1, K2,
H1, H2,
G1, G2

J1, J2,
K1, K2,
H1, H2,
G1, G2,
A1, A2,
A3, A4,
A5, A9,
B1, B2,
B3, B4,
B5, B9,
C1, C2,
C5, C6,
C7, C8,
D3, D4,
D5, D7,
E3, E4,
T8, T9,
U8, U9

E1, E2,
F2, F3,
G2, G3,
G1, H1

There are a number of non-functional pins that must
be dealt with appropriately.

10 High speed layout considerations

Due to the high speed nature of many of the interfaces on the S32R274 device attention has to be paid to the PCB layout to
ensure the integrity of these signals. When performing the layout of your circuit please consider the following:

• Differential pair routes must be impedance matched as well as length matched between all data lanes and the clock

lane.

• Differential pair routes should be kept as short as possible. Place any connectors as close to the S32R274 device as you

can to minimize board trace length.

• All differential signals should be routed on the same board layer so they all see the same parasitics. Ideally this would

be the top or bottom layer. Eliminate vias if at all possible. If vias must be used, make sure they are used across all
lanes.

• Use the following steps to reduce crosstalk in either microstrip or stripline layouts:

High speed layout considerations

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

48

NXP Semiconductors

«
...
46
47
48
49
50
»

Содержание S32R27



















































Отзывы:

Нет отзывов

Похожие инструкции для S32R27

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренд: Namron Страницы: 3

Бренд: YOKOGAWA Страницы: 150

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренд: Carel Страницы: 36

Бренд: Melexis Страницы: 13

Бренд: NI Страницы: 28

Бренд: Fairchild Страницы: 4

HYGRASREG KH-10

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Samson Страницы: 20

Бренд: Famco Страницы: 113

Бренд: THOMSON Страницы: 18

Бренд: ZoneVu Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды