manualshive.com logo in svg

NXP Semiconductors RDGD31603PSMKEVM, Руководство пользователя, Страница: 34 / 39

Поделиться
Скачать
NXP Semiconductors RDGD31603PSMKEVM Скачать руководство пользователя страница 34

NXP Semiconductors

UM11697

RDGD31603PSMKEVM three-phase inverter kit

Figure 33. Connecting the FRDM-KL25Z, translator board, and the RDGD31603PSMKEVM

6.1 Start using the kit

To get started using the RDGD31603PSMKEVM:

•

Assemble the KL25Z microcontroller board, the translator board and the three phase

board together, as shown in 

Figure 33

, on the eMPack module.

•

Connect the KL25Z via USB to a computer with FlexGUI software installed.

•

Supply the board with 12 V DC (1.0 A compliance current) through J1. See 

Figure 5

 for

polarity and location.

•

Check and adjust auxiliary supplies:

1. Set each VEE voltage (in the range -1.25 V to -7.5 V) using the six left-most

potentiometers shown in Fig.5. For example, adjust R239 to set the VEE voltage of

phase W low-side, measuring between the VEELW and GNDLW test points.

2. Set the VCC+VEE voltage for both low-side and high-side devices, by adjusting R235

and R265 respectively, until the desired VCC voltage is achieved.

Connection with the FlexGUI software can now be started to configure and check the

driver status.

UM11697

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 1 — 10 December 2021

34 / 39

Содержание RDGD31603PSMKEVM








































Отзывы:

Нет отзывов