NXP Semiconductors OM40006 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 23

NXP Semiconductors OM40006 Скачать руководство пользователя страница 19

NXP Semiconductors

UM11079

IoT Module base board

UM11079_OM40006.docm

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2017, 2018. All rights reserved.

User manual

Rev. 1.0

— March 20, 2018

19 of 23

8.5 Digital Microphone

A low power Knowles SPH0641LM4H digital microphone is incorporated on the board,
for use with Modules that support direct interfacing to this type of PDM microphone. Note
that the Knowles digital microphone is designed to be mounted on the underside of a
board, with audio passing through a hole in the board.

8.6 USER button

User Button (SW5) can be used to generate an interrupt by pulling down the P6 pin 41
(PIO1-1) of the Module to ground.

A 100KΩ pull-up resistor is also connected to this pin.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
17
18
19
20
21
...
»

Содержание OM40006
























Отзывы:

Нет отзывов