NXP Semiconductors OM40006 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 23

NXP Semiconductors OM40006 Скачать руководство пользователя страница 16

NXP Semiconductors

UM11079

IoT Module base board

UM11079_OM40006.docm

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2017, 2018. All rights reserved.

User manual

Rev. 1.0

— March 20, 2018

16 of 23

Pin

J8 signal

Expansion port connection

5

GND

GND

6

VDD (3.3V)

VDD (3.3V)

7

GPIO/INT (out/in)

P5 pin 21 (P2_0)

8

GPIO/RESET (out)

P5 pin 89 (P3_11)

9

SCL

P5 pin 75 (P3_24)

10

SDA

P5 pin 77 (P3_23)

11

GND

GND

12

VDD (3.3V)

VDD (3.3V)

This connector shares SPI interface signal connections with the Arduino expansion
connector J9.

The I

2

C interface signal connections used for this connector are shared with the Arduino

expansion connector J9, and are also connected to the accelerometer and the touch
screen controller.

Note that the Base Board includes 2.2kΩ pull-ups for the I

2

C interface

signals.

6.5 Arduino UNO expansion connectors

The OM40006 board includes four expansion connectors (J9-J12) compatible with
Arduino UNO revision 3. These connectors provide access to I

2

C, USART, SPI and

several GPIO/INT/PWM connections. Note that several of the signals available at these
connectors are shared with other connectors or board functions, so might not be usable if
those other functions are being used by other devices.

Table 5 below shows the connector circuit references and purposes.

Table 5.

Expansion connectors

Reference

Description

J9

Arduino Uno rev3 Digital 15:8, AREF, SDA & SCL connector. Also includes
two interrupt / PWM connections.

J11

Arduino Uno rev3 Digital 7:0. Includes 6 interrupt/GPIO/PWM signals and
USART interface.

J10

The even numbered pins 6

– 20 are compatible with the Arduino Uno rev3

Power connector standard.

J12

Arduino Uno rev3 Analog connector. Provides 3 ADC connections plus 3
GPIO/interrupt signals.

Below shows the sharing of signals between the expansion connectors and other
connectors or circuit functions. Refer to the board schematics for more details.

Table 6.

Expansion Connector signal sharing

Function Connector

Shared with

I

2

C

J9 pin 14 & 15

Accelerometer, PMod Connector, Audio Codec, LCD
touch panel controller

SPI

J9 pins 9, 11,13,15

PMod Connector

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
14
15
16
17
18
...
»

Содержание OM40006
























Отзывы:

Нет отзывов