NXP Semiconductors MIMXRT1050 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 19

NXP Semiconductors MIMXRT1050 Скачать руководство пользователя страница 14

Specifications

MIMXRT1050 EVK Board Hardware User’s Guide, User's Guide, Rev. 2, 03/2018

14

NXP Semiconductors

J24

J25

D8/CLKO/ICP1

NC

D9/OC1A/PWM

IOREF

D10/SPI_CS

RESET

D11/OC2A/PWM/SPI_MOSI 3.3V

D12/SPI_MISO

5V

D13/SPI_CLK

GND

GND

GND

AREF

VIN

D14/I2C_SDA

D15/I2C_SCL

2.14. Camera Module Connector

One parallel CSI (Camera Sensor Interface) is supported by the i.MX RT1050. There is a Camera
Module Connector (J35) on the MIMXRT1050 EVK Board. The CA031C based on OV7725 can be
used directly.

2.15. User Interface Switch

There are four user interface switches on the MIMXRT1050 EVK Board. Their functionality is as
below.

2.15.1. Power Switch

SW1 is a slide switch to control the power of the MIMXRT1050 EVK Board when the power supply is
from J2. The function of this switch is listed below:

•

Sliding the switch to the ON position connects the 5V power supply to the Evaluation board
main power system.

•

Sliding the switch to OFF position immediately removes all power from the board.

2.15.2. ON/OFF Button

SW2 is the ON/OFF button for MIMXRT1050 EVK Board. A short pressing in OFF mode causes the
internal power management state machine to change state to ON. In ON mode, a short pressing

«
...
12
13
14
15
16
...
»

Содержание MIMXRT1050




















Отзывы:

Нет отзывов