NXP Semiconductors LPC5410x Скачать руководство пользователя | Manualshive

Страница: 175 / 463

background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016

176 of 464

NXP Semiconductors

UM10850

Chapter 13: LPC5410x SCTimer/PWM (SCT0)

13.6.1.1 Counter configuration and control registers

The SCT contains two registers for configuring the SCT and monitor and control its
operation by software.

•

The configuration register (CONFIG) configures the SCT in single, 32-bit counter
mode or in dual, 16-bit counter mode, configures the clocking and clock
synchronization, and configures automatic limits and the use of reload registers.

•

The control register (CTRL) allows to monitor and set the counter direction, and to
clear, start, stop, or halt the 32-bit counter or each individual 16-bit counter if in
dual-counter mode.

13.6.1.2 Event configuration registers

Each event is associated with two registers:

•

One EVn_CTRL register per event to define what triggers the event.

•

One EVn_STATE register per event to enable the event.

13.6.1.3 Match and capture registers

The SCT includes a set of registers to store the SCT match or capture values. Each match
register is associated with a match reload register which automatically reloads the match
register at the beginning of each counter cycle. This register group includes the following
registers:

•

One REGMODE register per match/capture register to configure each match/capture
register for either storing a match value or a capture value.

•

A set of match/capture registers with each register, depending on the setting of
REGMODE, either storing a match value or a counter value.

•

One reload register for each match register.

13.6.1.4 Event select registers for the counter operations

This group contains the registers that select the events which affect the counter. Counter
actions are limit, halt, and start or stop and apply to the unified counter or to the two 16-bit
counters. Also included is the counter register with the counter value, or values in the
dual-counter set-up. This register group includes the following registers:

•

LIMIT selects the events that limit the counter.

•

START and STOP select events that start or stop the counter.

•

HALT selects events that halt the counter: HALT

•

COUNT contains the counter value.

The LIMIT, START, STOP, and HALT registers each contain one bit per event that selects
for each event whether the event limits, stops, starts, or halts the counter, or counters in
dual-counter mode.

In the dual-counter mode, the events can be selected independently for each counter.

«
...
173
174
175
176
177
...
»

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Бренд: UCS Страницы: 4

Бренд: Jabra Страницы: 8

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: Frico Страницы: 12

Бренд: Acuity Controls Страницы: 5

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

multicomp F144-MS-1V1C1TI6RO-3

Бренд: KBR Страницы: 68

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: ST Страницы: 40

Бренд: Varian Страницы: 37

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 142

DMX-LED-DIMMER X9 HR

Бренд: DMX4ALL Страницы: 14

Бренд: YASKAWA Страницы: 157

ControlPlex CPC12 T Series

Бренд: E-T-A Страницы: 30

IN1BN-DKC0-100-C0

Бренд: InPlay Страницы: 11

Бренд: Pilz Страницы: 21

Digital plus Set-01

Бренд: Lenz Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды