NXP Semiconductors LPC5410x Скачать руководство пользователя | Manualshive

Страница: 140 / 463

background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016

141 of 464

NXP Semiconductors

UM10850

Chapter 11: LPC5410x Group GPIO input interrupt (GINT0/1)

11.4.1 Grouped interrupt control register

11.4.2 GPIO grouped interrupt port polarity registers

The grouped interrupt port polarity registers determine how the polarity of each enabled
pin contributes to the grouped interrupt. Each port is associated with its own port polarity
register, and the values of both registers together determine the grouped interrupt.

Each register PORT_POLm controls the polarity of pins in port m.

11.4.3 GPIO grouped interrupt port enable registers

The grouped interrupt port enable registers enable the pins which contribute to the
grouped interrupt. Each port is associated with its own port enable register, and the values
of both registers together determine which pins contribute to the grouped interrupt.

Each register PORT_ENm enables pins in port m.

Table 172. GPIO grouped interrupt control register (CTRL, addresses 0x4001 0000 (GINT0) and 0x4001 4000 (GINT1))

bit description

Bit

Symbol

Value

Description

Reset value

0

INT

Group interrupt status. This bit is cleared by writing a one to it. Writing zero has no
effect.

0

0

No request. No interrupt request is pending.

1

Request active. Interrupt request is active.

1

COMB

Combine enabled inputs for group interrupt

0

0

Or. OR functionality: A grouped interrupt is generated when any one of the enabled
inputs is active (based on its programmed polarity).

1

And. AND functionality: An interrupt is generated when all enabled bits are active
(based on their programmed polarity).

2

TRIG

Group interrupt trigger

0

0

Edge-triggered.

1

Level-triggered.

31:3

-

-

Reserved. Read value is undefined, only zero should be written.

0

Table 173. GPIO grouped interrupt port polarity registers (PORT_POL[0:1], addresses 0x4001 0020 (PORT_POL0) to

0x4001 0024 (PORT_POL1) (GINT0) and 0x4001 4020 (PORT_POL0) to 0x4001 4024 (PORT_POL1)
(GINT1)) bit description

Bit

Symbol

Description

Reset value Access

31:0

POL

Configure pin polarity of port m pins for group interrupt. Bit n corresponds to pin
PIOm_n of port m.
0 = the pin is active LOW. If the level on this pin is LOW, the pin contributes to
the group interrupt.
1 = the pin is active HIGH. If the level on this pin is HIGH, the pin contributes to
the group interrupt.

1

-

«
...
138
139
140
141
142
...
»

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Бренд: Falcon Страницы: 3

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: Häfele Страницы: 24

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: Valcom Страницы: 6

Бренд: J+J Страницы: 4

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Controller CR100

Бренд: Sonos Страницы: 12

Бренд: Samcen Страницы: 65

WFHC 06Z 02 HC RF 24

Бренд: Watts Страницы: 18

Errata MSP430F6779

Бренд: Texas Instruments Страницы: 27

Бренд: PXM Страницы: 15

Бренд: DAPAudio Страницы: 11

Бренд: Akytec Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды