NXP Semiconductors LPC11U1x Скачать руководство пользователя | Manualshive

Страница: 494 / 523

background image

UM10462

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 5.5 — 21 December 2016

494 of 523

NXP Semiconductors

UM10462

Chapter 24: LPC11U3x/2x/1x Appendix ARM Cortex-M0

24.5.3.5 System Control Register

The SCR controls features of entry to and exit from low power state. See the register
summary in

for its attributes. The bit assignments are:

24.5.3.6 Configuration and Control Register

The CCR is a read-only register and indicates some aspects of the behavior of the
Cortex-M0 processor. See the register summary in

for the CCR attributes.

The bit assignments are:

[2]

SYSRESETREQ

WO

System reset request:

0 = no effect

1 = requests a system level reset.

This bit reads as 0.

[1]

VECTCLRACTIVE

WO

Reserved for debug use. This bit reads as 0. When
writing to the register you must write 0 to this bit,
otherwise behavior is Unpredictable.

[0]

-

-

Reserved.

Table 445. AIRCR bit assignments

Bits

Name

Type

Function

Table 446. SCR bit assignments

Bits

Name

Function

[31:5]

-

Reserved.

[4]

SEVONPEND

Send Event on Pending bit:

0 = only enabled interrupts or events can wakeup the processor,
disabled interrupts are excluded

1 = enabled events and all interrupts, including disabled interrupts,
can wakeup the processor.

When an event or interrupt enters pending state, the event signal
wakes up the processor from WFE. If the processor is not waiting for
an event, the event is registered and affects the next WFE.

The processor also wakes up on execution of an

SEV

instruction.

[3]

-

Reserved.

[2]

SLEEPDEEP

Controls whether the processor uses sleep or deep sleep as its low
power mode:

0 = sleep

1 = deep sleep.

[1]

SLEEPONEXIT

Indicates sleep-on-exit when returning from Handler mode to Thread
mode:

0 = do not sleep when returning to Thread mode.

1 = enter sleep, or deep sleep, on return from an ISR to Thread
mode.

Setting this bit to 1 enables an interrupt driven application to avoid
returning to an empty main application.

[0]

-

Reserved.

«
...
492
493
494
495
496
...
»

Содержание LPC11U1x












































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC11U1x

Бренд: Idesco Страницы: 11

Бренд: Yamaha Страницы: 5

VENMAR ADVANCED TOUCHSCREEN CONTROL

Бренд: vanEE Страницы: 4

Бренд: GOAL ZERO Страницы: 52

Бренд: Wavelength Electronics Страницы: 17

Бренд: GIESSE Страницы: 136

Бренд: NDS Страницы: 20

Бренд: Qorvo Страницы: 45

Бренд: GEM Страницы: 2

CY3250-PLC20QFN

Бренд: Cypress Страницы: 2

TROVIS 6495 Series

Бренд: Samson Страницы: 156

Бренд: Linak Страницы: 8

Бренд: Vent-Axia Страницы: 4

Бренд: MICROMATIC Страницы: 10

Бренд: Spirax Sarco Страницы: 20

Smatrix Wave PLUS

Бренд: Uponor Страницы: 4

Бренд: Beltrame Страницы: 46

Бренд: DUNIWAY Stockroom Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды