NXP Semiconductors FRDM-K28F Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 22

NXP Semiconductors FRDM-K28F Скачать руководство пользователя страница 9

MCU

Freedom Board for Kinetis K28F (FRDM-K28F), User's Guide, Rev. 0, 04/2017

NXP Semiconductors

9

Figure 5. SWD debug connector

The J23 header is populated by default. A mating cable (such as the Samtec FFSD IDC cable) can then
be used to connect the OpenSDA v2.2 of the FRDM-K28F to an off-board SWD connector.

3.2.2. Virtual serial port

A serial port connection is available between the OpenSDA v2.2 MCU and pins PTC24 and PTC25 of
the K28 MCU.

4. MCU

FRDM-K28F features the MK28FN2M0VMI15 MCU. This 150 MHz MCU is a part of the Kinetis K2x
family and it is implemented in the 169 MAPBGA and 210 WLCSP (K28 only) packages. The
FRDM-K28F board also supports the K27 and K28 MCUs. The following table describes some of the
features of the MK28FN2M0VMI15 MCU that is populated on this board.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
7
8
9
10
11
...
»

Содержание FRDM-K28F























Отзывы:

Нет отзывов