NVT NV-ET1801 Скачать руководство пользователя страница 3

Страница: 3 / 15

CONFIGURATION INSTRUCTIONS

The NV-ET1801 TBus transmitter delivers high bandwidth encrypted Ethernet signals over virtually any kind of wire (Coax, UTP, STP, Un-twisted
wire, etc.). To provide utmost signal integrity and security, the NV-ET1801 transceivers

must be configured

to communicate exclusively with other

transceivers within their

TBus Network Group

. This group typically consists of one or more remote Transmitters, typically located at the IP camera

and one Receiver, typically located at the control-room. Transmitters may be the NV-ET1801 or NV-ET1804. The Receiver may be the NV-ET1801,
NV-ER1804, NV-ER1808i, or NV-ER1816i.

Before functioning on the network,

each NV-ET1801 must learn which other transceivers are to be part of that group

. This simple process

is called Joining. It is recommended that transceivers in each Network Group be configured prior to deployment using these instructions:

Step One: Gather Materials

• All 1800 series Transceivers

• Device labels

• RJ45 patch-cord

• IP Network Documentation Log

• Small paper-clip, partially straightened

Step Two: Connect Hardware

• Remove and discard the “Configure Before Use” labels.
• Use an RJ45 or BNC patch-cord to connect the TBus ports

of two Transceivers.

CAUTION: Never connect the RJ45 TBus port to an
RJ45 ethernet port

• Apply power to one of the TBus devices.
• The blue POWER LED on each Transceiver will blink for 8 seconds and then go on.
• After 20 seconds, verify that the green TBus Link LED on each transceiver is off.

If a TBus Link LED is on, the Transceiver has been previously joined.
Perform the un-joining process below before proceeding.

Step Three: Joining

• On Transceiver #1, using the straightened paper-clip, momentarily depress and release the small JOIN push-button

located on the bottom of the unit. Its blue Power LED will begin blinking.

• Depress and release the same push-button on the Transceiver #2. Its blue Power LED will begin blinking.
• Both Transceivers have now entered

Join Mode

. They will find each other and establish encrypted communication.

In about 10 seconds, the blue Power LEDs on both Transceivers will return to a steady on condition, and
their green TBus Link LEDs will illuminate, indicating a successful

Join

• One TBus Link LED will remain on solid. The other may wink with data.

Step Four: Adding Transceivers

(if required)

• Disconnect Transceiver #1 and replace it with a new un-joined Transceiver.
• Repeat steps two and three to add additional Transceivers to the same

Network Group.

Step Five: Documentation

• Label the configured Transceivers with a unique Network Group ID of your choice.

This will help you identify them after they have been deployed.

• Record this Network Group information in your IP Network Documentation Log:

• Camera Number

• Camera-end NVT Transceiver MAC Address

• Camera Position/Location

• NVT Transceiver Network Group Name

• Camera Make & Model

• Control Room NVT Transceiver MAC Address

• Camera MAC & IP Address

• Control Room Router Port Number

• Camera Login & Password

This log may include essential documentation which will help you identify all system devices during
and after deployment. The NV-ER1808i and NV-ER1816i user interfaces have data-entry fields for
this purpose.

Un-Joining a Transceiver

If you need to move a Transceiver from one Network Group to another, it must first un-learn its
previous Network Group and be returned to an un-joined state. Do this by:

• Apply power.
• The blue POWER LED on each Transceiver will blink for 8 seconds and then go on.
• Using the straightened paper-clip, depress the small JOIN push-button until the blue Power LED goes off (about 13 seconds).
• Un-joining is now complete.

If you are not sure that un-joining has been successful, remove and then re-apply power, and repeat.

Page 3 of 15