NV1073KB
•
DRIVING LIGHT KIT
•
OWNER
'
S MANUAL
NVISIONLIGHTING.COM
1-800-835-0129
MOUNTING INSTRUCTIONS
Lamps must be mounted at the following heights from the road:
REQUIRED TOOLS:
Center punch and hammer
Electric drill
13/32" = 1/8" drill bit
Screwdriver
Wire cutters/strippers and crimpers
Wrenches
BELOW BUMPER MOUNTING
1. Before mounting lights below the bumper, remove lens and reflector.
Replace them in the reverse position so that the ideal beam pattern will be
maintained.
2. Drill a 1/2" (13mm.) diameter hole through desired mounting position and
install the lamp on the bumper, using the bolt/nut and lock washer provided
with each lamp. Tighten the nut to retain aiming position depending on type of
lamp. Make sure both lights are grounded.
KIT CONTAINS
A. Lamp connect wire (Blue) - about 4 feet (120CM). 1pc.
B. Main power wire (White) - about 12 feet (360cm) 1 pc.
C. Power supply wire (Black) - about 8 feet (240cm) 1 pc.
D. Illuminated rocker switch 1 pc.
E. Assembled automotive lamps 2 pcs.
F. Screws 2 pcs.
G. Ground wire 1 foot (30cm)1 pc.
WIRING INSTRUCTIONS
1. Disconnect car battery to avoid short
circuits/electrical shock.
2. Usethe wire provided as diagram 1):
3. Connect the male terminal of one lamp to the “Y” connector of the main
power wire (B). Conncet the male terminal of the second lamp to the female
terminal of the lamp wire (A to the “Y” connector of main power wire (B).
4. Mount switch provided under dash within easy reach of driver.
5. The other end of the main power wire (B) should be led through the firewall
using exisiting wire harness. Connect to switch terminal. Secure the wire along
the way with tie-clips to prevent any movement of the wire or contact
with high-tempeture engine parts.
6. The power supply wire (C) with the 15-amp in-line safety fuse connects to
the remaining switch terminal. The other end of the power supply wire (C) must
be connected to either the car’s fuse box or the positive (+) terminal of
the battery.
7. Recconect car battery after confirming all the wiring is identical with the
above diagram.
DRIVING LAMPS.
Driving lamps shall be aimed with the center of the high instensity zone
on a verticle line straight ahead of the lamp center and 2" (51mm) below
the level of the lamp center at a distance of 25ft. (7.62m) from the lens
as shown in figure 2
FOG LAMPS.
Fog lamps shall be aimed with the center of the high intensity zone on the
verticle line straight ahead of the lamp center and with with the top edge of
the beam 4" (102mm) below the level of the lamp senter at a diastance of 25ft
(7.62m) from the lens as shown in figure 1.
TYPE
LAMP
MEDIUM
HEIGHT
MAXIUM
HEIGHT
FOG
12in. (30cm.)
30in. (75cm.)
DRIVING
16in. (40cm.)
42in. (105cm.)
Vertical Center Line
Ahead of Left Lamp
Figure 1
4"
Car
Axis
Vertical Center Line
Ahead of Right Lamp
Height of Lamp
Centers
Aim Right Lamp
Same as Left
2"
Figure 2
Vertical Center Line
Ahead of Left Lamp
Car
Axis
Vertical Center Line
Ahead of Right Lamp
Height of Lamp
Centers
Aim Right Lamp
Same as Left
Lamps
Lamps
“Y” Connector
Main Power
Wire (B )
Power Supply
Wire (C)
To Fuse Bo x
or (+) Terminal
of Battery
Switch
Terminal
Cover
Lamp
Wire
(A)
Ground
Wire
WARNING!
Vehicles with front seat airbag restraint devices may have airbag senors
embeded in the vehicles front bumper. Before beginging installation of
this product on your vehicle, throughly check your vehicle’s owner manual
for information regarding the location of airbag sensors on your vehicle.
Disturbance of the fron bumper by drilling or other means could cause damage
to an airbag sensor, or cause an airbag to inflate in the vehicle.
DO NOT INSTALL THIS PRODUCT IN OR ON THE FRONT BUMPER IF THE
OWNER’S MANUAL INDICATES IT IS INADVISABLE!
Hopkins Manufacturing Corp. assumes no liability whatsoever for any damage
caused to a vehicle or any portion of an airebag restraint system during
installation of this product. Likewise, we assume no liability whatsoever for
any damages or expenses incurred or caused by the installation of an airbag
devise durning installation of this product.
Hopkins Manufacturing Corporation
Emporia, KS 66801
www.nVisionLighting.com
© Copyright 2018 Rev A
