nvent RAYCHEM H908 Скачать руководство пользователя страница 10

Страница: 10 / 14

10 | nVent.com

1/4 in

Note: Ring of adhesive

will appear at both ends

Heat-shrink tube

Plug-in cord

Green wire

Black and

white wires

Mastic

• Use insulated bus wire

crimps and CT-100 crimp

tool to connect black and

white wires to bus wires

of heating cable. Polarity

does not matter.

• Remove release paper from mastic strips.
• Wrap one strip of mastic around the white

wire against the end of the splice

to provide a water block.

• Repeat for the

black wire.

Finish bus wire preparation

Apply 5-inch shrink tube

Connect bus wires

Apply mastic to bus wires

• Trim bus wires.

• Squeeze the

mastic together.

• Center the 5-inch heat-shrinkable tube over

the splice. Make sure tube extends over the

end of each heating cable and the cord.

• Shrink the tube completely. Start at the

middle and work toward each end.

Keep heating after tube has shrunk,

to melt mastic and adhesive inside

tube. Total heating time should

be about 2 minutes.

• Immediately after shrinking, pinch first one

end of the tube and then the other end with

needle-nose pliers until the ends stay sealed.

This normally takes 10 seconds per end.

Содержание RAYCHEM H908















Результаты поиска

Содержание RAYCHEM H908

Отзывы:

Бренды по названию

Популярные бренды

nvent RAYCHEM H908, Руководство по установке

Результаты поиска

Содержание RAYCHEM H908

Отзывы:

Бренды по названию

Популярные бренды