Nuvo NV-T2SIR, Руководство по установке, Страница: 14 / 30

9
Once the audio outputs are set at Standalone, the T2SIR offers
three methods for IR control. One is to take the IR output of
your control device using a mono 3.5mm patch cable plugged
into the Direct IR input on the back panel of the T2SIR. Tuners A
and B feature discrete commands, allowing both Tuners to be
controlled independently from one input. The second method
for IR control is to attach an IR emitter over the IR receiver on
the front panel, and the third method is to aim the remote
control at the IR receiver located on the front panel.
RS232 Serial Control
The T2SIR features a bidirectional DB9 port for serial control.
This enables the Tuner to be controlled via a third party home
automation system and will in turn issue present state
commands back to the controller. Potentially, all aspects of
NuVoNet communication can be emulated using the serial
control capability. The necessary protocol for serial use can be
downloaded from the NuVo website ProZone at
www.nuvotechnologies.com/prozone.
SYS ON
EXT. MUTE
SYSTEM ZONE TRIGGER OUTPUTS NETWORK
SUM1
EMITTER OUTPUTS
3033118
C US
R
CONFORMS TO
UL STD.6500
CERTIFIED TO
CAN/CSA STD.E60065
NuVo Technologies Cincinnati Ohio USA
FUSE:T5 A 120V 60Hz 500W
MODEL NV-I8M
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
www.nuvotechnologies.com
DIGITAL LINK
VARIABLE
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R
VARIABLE
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R
VAR.
OUT
FIX.
OUT
PROGRAM
1 2 3 4 1 2 3
CONNECT TO
NV-I8X
USE NV-SLC1
CABLE
CONNECT TO
NV-I8EZP1
USE NV-NC1
CABLE
USE CNLY WITH 250V FUSE
4 5 6 SUM2 5 6 7 8
ZONE 5 ZONE 6 ZONE 7 ZONE 8
RS 232
SPEAKER
40W/6 OHMS X 2
LEFT RIGHT
SPEAKER
40W/6 OHMS X 2
LEFT RIGHT
SPEAKER
40W/6 OHMS X 2
LEFT RIGHT
0728
3033118
RT E E T K
N I
CM
Model NV -T2 SIR
Dual SIRI US Ready AM/FM Tuner
www.nuvot echno logi es. com
NuVo Techno log ies LLC Hebr on, KY USA
•
CONFORMS TO UL
STD.60 065 CERTIFIED
TO CAN/CSA STD.
C22.2 No.60 065:0 6
RS 232
SYS TE M
NuVoNet IR INPUT
RoHS
Fig. 5
Fig. 6
Fig. 7
II. T2SIR Use with SIRIUS Radio
The SIRIUS 8-Pin Connector (Fig. 6)
Each Tuner, A and B, has a SIRIUS-Ready connector on its back
panel. This connector is ready to receive the Tuner signal and
related metadata from a SIRIUS receiver. Any SIRIUS receiver
equipped with the SIRIUS connector will communicate with the
T2SIR's input. The cable necessary for this connection is
typically supplied with the SIRIUS receiver. Once the 8-pin
connection is made from the SIRIUS receiver to the T2SIR,
SIRIUS will be recognized as a radio band.
SIRIUS Modules and Subscription (Fig. 7)
There is not a specific SIRIUS receiver that must be used in
conjunction with the T2SIR. Several are on the market, and the
only pre-requisite is that the receiver used has the 8-pin
SIRIUS-Ready connector. NuVo does have the NV-SCH1 home
receiver module as a convenient, inexpensive solution for the
T2SIR. Each SIRIUS Tuner has an ID associated with it. This
number is typically found printed on the SIRIUS Tuner or by
going to the T2SIR SIRIUS Info menu. Each attached SIRIUS
receiver must be activated using its ID number.
ANTENNA
IN
USE NV-T2FAA
ANTENNA
L
AUDIO
R
TUNER A
SIRIUS
L
AUDIO
R
TUNER B
SIRIUS
SIRIUS-Ready 8-pin connectors
ANTENNA
IN
USE NV-T2FAA
ANTENNA
L
AUDIO
R
TUNER A
SIRIUS
L
AUDIO
R
TUNER B
SIRIUS
Diagram shown using a NV-SCH1 SIRIUS Home Tuner