Adjust the microphone sensitivity using the “+ -“ button to
acuire your desirable sound volume. The TRANSMIT indicator
will blink everytime these buttons are pressed, more number
of blinks mean the microphone is more sensitive to sound
(maximum is 5 blinks and minimum is 1 blink). Press + to
increase and – to decrease the microphone sensitivity.
Once the BU is in transmit mode, the TRANSMIT indicator
will light up RED. The unit will return to standby mode a few
seconds after the microphone stops picking up any sound
and the TRANSMIT indicator goes off.
This baby monitor is equipped with LISTEN & TALK and
LULLABY function so that the parent can speak or play
3.
4.
5.
6.
7.
8.
lullabies to comfort baby. The volume of parent’s voice or music from speaker on BU can be adjusted by
press the “+ -“ button on BU.
Note: While there is music or parent’s voice heard from speaker, the “+ -“ button can be used to
adjust volume. Under normal mode when there is no sound from speaker, the “+ -“ button will only
adjust the microphone sensitivity.
The starry night projector can be set to permanently ON or VOX (voice activated) remotely by the PU. Under
VOX mode, the starry night projector is switched on once the microphone detects a sound and goes off a
few seconds after the microphone stops picking up any sound. The starry night can be projected on the
ceiling or wall by making the BU to stand on its support lever.
Press the FEEDING TIMER button on BU to initiate the feeding timer countdown in PU, beep sound 2 times
will be heard. The PU screen will show icon B flashing and once the set period has elapsed, an alarm will be
heard and icon B show flashing to remind parents to feed the baby.
Note: If the PU feeding time setting is changed after pressing FEEDING TIMER button on BU, the
feeding countdown will follow the previous setting time. the new-set feeding time will only be in
effect by pressing FEEDING TIMER button on BU again after the change of PU feeding time setting.
The temperature sensor inside unit detects the ambient temperature and its current reading is shown on
the PU screen. The normal operating range of sensor is -19º C(-20˚F) to + 50º C(122˚F). Temperature outside
this range will be shown as “- -“ on the PU screen. In case there is a sudden big temperature change (e.g.
you bring out the unit from indoor to outdoor during winter time), the sensor may need to take a few
minutes before it can adapt to the new environment and show the correct reading on the PU screen.
PARENT UNIT
1.
2.
3.
4.
Rotate the side ring clockwise or anti-clockwise to switch on the unit (Clockwise – vibration ON /Anti-
clockwise – vibration OFF).
The PU screen will auto-sleep in around 20 sec if there is no sound from baby.
Normally, the POWER indicator will show GREEN. When battery is running out, it will start FLASHING GREEN.
Once the unit is under charge, this indicator will show RED.
To enter setting mode, long press the button 13 for 2 seconds. The PU screen will show either following:
This process is to match the PU with BU and Baby motion sensor mat so that they can communicate with each
other while no other devices (even baby monitor of identical model) can interfere with you or receiving your
signal.
The PU and BU are already paired when they are shipped from factory. However, it is necessary to perform
pairing again when extra BU is added to work with the PU.
PAIRING
PAIRING PARENT UNIT (PU) AND BABY UNIT (BU)
1.
2.
3.
4.
5.
Press Hold button 13 of PU.
Rotate the side ring to switch on unit, then release
button 13 after Beep sound. The icon screen will
show “1” and “P” flashing.
Press Hold button “+” of BU and Set ON/OFF switch
to “ON” position until the TRANSMIT indicator
lights up, then release “+” button. The TRANSMIT
indicator will start flashing. Repeat same procedure
for the other BU, if any.
Press the FEEDING TIMER button on one of the BU,
the TRANSMIT indicator becomes steady and beep
sound 2 times will be heard.
At the same time, “P” icon on PU screen will stop
flashing which represent the pairing process is
performed successfully. This BU will be BU No 1.
Now press button 15 on PU, the PU screen will
show “ 2 ” and a “ P ” flashing.
Repeat step 3-4 for the other BU. The “ P ” on PU
screen will stop flashing which represent the
pairing process is performed successfully. This BU
will be BU no. 2.
Switch off all the units and switch them on again,
the baby monitor is now ready for operation.
In case the PU and BU cannot communicate with
each other, repeat pairing process again.
6.
7.
8.
9.
PAIRING BABY MOTION SENSOR MAT
10.
11.
12.
13.
The pairing between BU and Baby Motion Sensor Mat should be performed after the successful pairing
between BU and PU or otherwise the system will not operate properly.
Set the BU into pairing mode by repeating step 3 above.
While pressing down the alarm hold button 21 on Mat, switch on the Mat by turning the knob 20 clockwise,
now release hold button 21. Press the feeder timer button 4 on BU, the TRANSMIT indicator shows steady
on and beep sound 2 times will be heard from the BU, indicating the pairing is successful. In case you have
2 Baby Motion Sensor Mats to be paired to two BU, Please pair each one in turn with the other BU being
switched off.
Switch off both the BU and sensor mat, then switch on again for normal operation, probably you will hear
the abnormal breathing alarm in PU after 20 sec in case nothing is placed on the Baby Motion Sensor Mat.
Slight tap the mat few times and the alarm will stop, this shows the system is working properly.
Note: When it is no longer necessary to monitor the baby’s breathing as he grows older, the Baby
Motion Sensor Mat is required to unpair from BU to avoid false alarm. To achieve this perform
pairing process again between PU & BU by repeating above steps 1-8, but leave out steps 11-13.
BABY UNIT
1.
2.
Set the power ON/OFF switch to ON position, the POWER indicator should light up STEADY GREEM, if it
starts flashing, the battery is running out. Either replace with new batteries or use the AC adapter as power
supply. The battery low alert of BU is also shown as icon “J”on PU screen.
Place the BU about 1m from the baby’s crib with the microphone facing towards the baby.
HOW TO USE
