manualshive.com logo in svg

Nuvation Energy High-Voltage BMS, Руководство по установке, Страница: 18 / 46

Поделиться
Скачать
Nuvation Energy High-Voltage BMS Скачать руководство пользователя страница 18

Table 13. Link Out: Molex Micro-Fit 3.0 Connector

Molex 43025-0400

Manufacturer

Molex Incorporated

Housing

43025-0400

Housing material

Nylon UL94V-0

Circuits

4

Crimp terminal

43030-0002

Wire gauge range

AWG20-24 stranded

Table 14. Link Out Connector Pin Assignment

Pin

Connection

Description

Connected to Device

1

VBUS

DC power from Stack Controller, with Fault
Pilot Signal

Cell Interface

2

COM

Power return from Stack Controller

Cell Interface

3

IPA

Link Bus differential pair plus

Cell Interface

4

IMA

Link Bus differential pair minus

Cell Interface

4.4.2. Link In

The Link In connector provides power and communication to this Cell Interface from the Cell Interface
modules below this Cell Interface, or from the Stack Controller if this Cell Interface is measuring the
most negative cell in the stack.

The amount of current sourced into this connector is the sum of current consumed by this Cell
Interface and all those above it (which amounts to all Cell Interface modules if this Cell Interface is
measuring Cell 1).

Connect to the Link Out connector on the Cell Interface that is measuring the previous series-
connected cell below this Cell Interface to this connector, or connect the Stack Controller to this
connector if this Cell Interface is measuring the bottom cell in the stack.

Nuvation Energy High-Voltage BMS - Installation Guide

Document ID: NE-IG-001

15

Rev 2.1, 2020-03-13

Содержание High-Voltage BMS















































Отзывы:

Нет отзывов